Bedienungsanleitung SureFlap Microchip Pet Door (Seite 10 von 265) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

782758

Zoom out

Zoom in

Vorherige Seite

1/265

Nächste Seite

7.2 Installation in wooden doors, plastic doors, or plasterboard walls

1. Place the external frame face down as in Figure 2. Attach a ball of Blu Tack (or similar

adhesive putty) in each of the four corners. These should allow you to stick the frame

to most doors.

2. Choose the position on the door at which you want to mount the pet door and stick

the frame to the door. To ensure that it is level we recommend you use a spirit level as

shown in Figure 3.

3. Run a sharpened pencil or pen around the inside edge of the frame where it would

touch the door. You need to make a legible line as this will be used for cutting against.

4. Remove the frame from the door and check you have a solid line (Figure 4). Before

you cut out the hole for the tunnel drill holes in all the corners large enough to allow

your jigsaw blade through, see gure 5. Cut out the tunnel hole with an electric jigsaw

–ensure you cut 2mm (1/16”) outside the line you have marked for the hole to allow

enough clearance for the tunnel, see Figure 6. Make sure that your jigsaw is sitting at

on the door at all times while cutting.

5. Clean o󰀨 any loose debris, dust and dirt from the door before you install the SureFlap

Microchip Pet Door.

6. Mount the pet door in the hole with the main assembly (battery covers and LCD

screen) inside the house. See Figure 7. Mount the external frame on the outside of

the house and mark the 4 screw holes. Using a drill with a 6mm (1/4”) diameter bit,

drill the holes for the screws. It is vital these holes are drilled straight to ensure the two

halves of the pet door connect properly.

7. Re-mount the pet door and the external frame on the outside of the house. Depending

on the thickness of the door, the tunnel will protrude through the frame by di󰀨ering

amounts. Under no circumstances should you cut or drill through the tunnel

as this contains the microchip reader and will prevent the unit from working

properly. Three di󰀨erent lengths of screw have been provided for your use. Choose

the correct screw length to suit the thickness of your door. If you are not sure, use the

smallest rst, if this is too short use the next size up. Take care not to use a longer

screw than needed, as this may damage the main assembly front face. Screw the

external frame to the main assembly. See Figure 8.

8. When the pet door has been mounted correctly, place the screw caps over the screw

holes on the external frame. Align the screw caps with the slot pointing outwards

and push rmly into place. See Figure 9. To remove the screw caps slide a at blade

screwdriver into the side slot and lever the cap out of the hole.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

SureFlap Microchip Pet Door Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info