Bedienungsanleitung Switel DC402 (Seite 79 von 100) (Deutsch, Englisch, Französisch, Italienisch)

687912

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

− Starting Up −

2 Starting Up

2.1 Safety information

Caution: It is essential to read the Safety Information in Chapter 1 before starting up.

2.2 Checking the contents of the package

The package contains:

a base station with power adapter plug

a telephone connection cable

two handsets four rechargeable batteries

a charging station with power adapter plug an operating manual

2.3 Connecting the base station

Position the base station within reach of the telephone line socket and a power outlet. Only

use the components supplied.

1. Insert the small plug on the power adapter plug cable in the corresponding socket

on the underside of the base station.

The plug cannot be connected incorrectly because the plug and socket are

designed in such a way to prevent reverse poling. The plugs must snap audibly into

the base station sockets.

2. Insert the small plug on the telephone connection cable in the corresponding socket

on the underside of the base station.

3. Feed both cables on the underside of the base station in the cable duct provided.

4. Plug the power adapter plug in a properly installed 230 Volt power outlet.

The power adapter plug from the base station must remain connected at all times.

5. Connect the telephone connection cable supplied in the telephone line socket.

2.4 Connecting the charging station

Connect the charging station as illustrated

in the diagram. For reasons of safety, only

use the power adapter plug supplied.

2.5 Inserting the batteries

Insert two batteries of the type AAA Ni−MH 1.2 V 550 mAh

in the battery compartment after opening it. Pay attention

to correct polarity (refer to Fig.)! Close the battery compart-

ment cover.

Important: Do not use any other type of batteries.

2.6 Charging the batteries

When preparing to use the handset for the first time, place it in the base station (display facing up-

wards) for at least 14 hours. The charging control lamp on the base station lights up. The handset

warms up during the charging process. This is normal and does not represent a risk. Do not

charge the handset with charging units from other manufacturers. Failure to charge the batteries

properly can lead to telephone malfunction.

The current battery charge status is indicated in the display:

Full Half empty Low Empty

2.7 Tone or Pulse dialling mode

The telephone can be connected to both analogue connections (pulse dialling) and digital con-

nections (tone dialling). The equipment is set to Tone dialling mode at the factory. If the telephone

does not work on your telephone connection, refer to Chapter 7.3 to learn how to switch the tele-

phone to analogue, pulse dialling mode.

2.8 Operating on private branch exchanges

If your telephone is connected to a private branch exchange, the R button can be used to imple-

ment the transfer calls or automatic callback functions. When used on a private branch exchange,

a Recall time of 90 ms must be set. The dealer where you purchased the exchange can provide

information as to whether the telephone will work properly with the exchange.

Mains power outlet

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Switel DC402 Seite 79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info