688288

Switel DET19073 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Playback and delete messages
The last recorded message is played first via the loudspeaker on model.
Old messages cannot be played again until after all new messages have
been played.
Playback recorded messages
1. Press the MENU key to enter menu selection.
2. Press the Navigation key to select ANSW MACHINE and then press
OK key to select.
3. Press the OK key to start playback.
* During message playback you can press MENU key, then Navigation
to select options to REPEAT the current message, skip forward to the
NEXT message, skip back to the PREVIOUS message or DELETE the
current message.
Delete all recorded messages
1. Press the MENU key to enter menu selection.
2. Press the Navigation key to select ANSW MACHINE and then press
OK key to select.
3. Press the Navigation key to select DELETE ALL and then press OK
key to select.
Using the intercom
Intercom, call transfer and conference are only possible with at least 2
handset registered to the same base station. It allows you to make free
internal calls, transfer external calls from one handset to another, and
set up a 3-way conference with two handsets and an external call.
If you try to make a call while another handset is already on an external
call, you’ll hear a busy tone for a few seconds before the display returns
to idle.
Intercom another handset
Press INT key in idle mode.
Intercom is established immediately if there are only 2 regi-
stered handsets.
If there are more than 2 registered handsets, the handset numbers
which are available for intercom, and a * , will be displayed. Press the
specific handset number you wish to call, or press * to ring all handsets,
to start intercom.
Transfer an external call to another handset
During the call, press INT key to put the external call on hold
(the caller can no longer hear you).
Intercom is established immediately if there are only 2 registered
handsets. If there are more than 2 registered handsets, the handset
numbers which are available for intercom, and a ’*’, will be displayed.
Press the specific handset number you wish to call, or press ’*’ to ring all
handsets, to start intercom.
Press TALK key on the called handset to answer the internal
call, where both internal callers can talk. Intercom is establis-
hed.
Press HANG-UP/EXIT button on the first handset to transfer
the external call to the called handset. The external call is
transferred.
** If there is no answer from the called handset, press INT key to resume
the external call.
Answer an external call during intercom
During intercom, a new call tone is emitted when there is an incoming
external call.
Press TALK key to answer the external call and end the in-
tercom. Connection with the external call is established.
** To put the internal call on hold and answer the incoming external call,
press INT key.
Switch between an internal and external call
During the call, press INT key to switch between an internal
or external call.
Establish a three-party conference call
The conference call feature allows one external call to be shared with
two handsets (in intercom). The three parties can share the conversation
and no additional network subscription is required.
During an external call, press INT key to put the external call
on hold (the caller can no longer hear you).
If there are more than 2 registered handsets, the handset numbers
which are available for intercom will be displayed. Press the specific
handset number you wish to call to start intercom.
Press TALK key on the called handset to answer the internal
call, where both internal callers can talk. Intercom is establis-
hed.
Press and hold INT key for 2 seconds on the first handset to
start the three-party conference.
CONFERENCE will be displayed on the screen once the
conference call is established.
Handset Tone
Set the ring volume
There are 5 ringer volume options (OFF, LEVEL 1, LEVEL 2, LEVEL 3
and LEVEL 4). The default level is LEVEL 3.
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select PERSONAL SET and then press
OK key to select.
3. Press the Navigation key to select HANDSET TONE and then press
OK key to select and show RING VOLUME. Press the OK key again to
select.
4. Press the Navigation key to your desired volume level and then press
OK key to confirm. A confirmation beep is played.
Set the ring melody
There are 10 ring melodies available on your handset.
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select PERSONAL SET and then press
OK key to select.
3. Press the Navigation key to select HANDSET TONE and then press
OK key to select.
4. Press the Navigation key to select RING TONES and then press OK
to select.
5. Press the Navigation key to your desired melody and then press OK
key to confirm. A confirmation beep is played.
Activate/deactivate key tone
A single tone is emitted when a key is pressed. You can enable or
disable the key tone. By default, the key tone is ON.
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select PERSONAL SET and then press
OK key to select.
3. Press the Navigation key to select HANDSET TONE and then press
OK key to select.
4. Press the Navigation key to select KEY BEEP and then press OK to
select.
5. Press the Navigation key to select ON or OFF and then press OK key
to confirm. A confirmation beep is played.
Activate/deactivate auto hang-up
This function enables you to end a call automatically by simply placing
the handset on the base station. By default, the Auto Hang up feature is
ON.
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select PERSONAL SET and then press
OK key to select.
3. Press the Navigation key to select AUTO HANG-UP and then press
OK key to select.
4. Press the Navigation key to select ON or OFF and then press OK key
to confirm. A confirmation beep is played.
Set date/time format
Set time format
You can set your preferred date/time format for your phone. The default
format is DD/MM and 24 HOURS.
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select CLOCK&ALARM and then press
OK key to select.
3. Press the Navigation key to select SET FORMAT and then press OK
key to select.
4. Press OK key to enter TIME FORMAT. The current setting is
displayed.
5. Press the Navigation key to select 12 HOURS or 24 HOURS and then
press OK key to confirm. A confirmation beep is played.
Set date format
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select CLOCK&ALARM and then press
OK key to select.
3. Press the Navigation key to select SET FORMAT and then press OK
key to select.
4. Press the Navigation key to select DATE FORMAT and then press OK
key to select. The current setting is displayed.
5. Press the Navigation key to select DD/MM or MM/DD and then press
OK key to confirm. A confirmation beep is played.
Set alarm
The handset has an alarm clock feature, and when the alarm is set, the
is shown on the handset display.
When the alarm time is reached, the display flashes -ALARM- and the
alarm melody is played for 1 minute or until any handset key is pressed.
If the alarm is set for ON DAILY and the alarm will sound again on the
next day. If the alarm was set for ON ONCE, the will be turned off.
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select CLOCK&ALARM and then press
OK key to select.
3. Press the Navigation key to select ALARM and then press OK key to
select.
4. Press the Navigation key to select OFF, ON ONCE or ON DAILY and
then press OK key to confirm.
If you select ON ONCE or ON DAILY, enter the time (HH-MM) for the
alarm and press the UP/DOWN key to select AM or PM if the time is in
12 HOURS format.
5. Press OK key to confirm. A confirmation beep is played.
Set alarm tone
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select CLOCK&ALARM and then press
OK key to select.
3. Press the Navigation key to select ALARM TONE and then press OK
key to select.
4. Press the Navigation key to select MELODY 1, MELODY 2 or
MELODY 3 and then press OK key to confirm. A confirmation beep is
played.
Advanced use of your telephone
Change Master PIN
The Master PIN is used for registration/unregistration of handsets and
for accessing the answering machine remotely. The default Master PIN
number is 0000. The maximum length of the Master PIN is 8 digits.
Note: If you forget your PIN code, you can reset it to its default 0000
using a handset Reset (page 15).
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select ADVANCED SET and then press
OK key to select.
3. Press the Navigation key to select CHANGE PIN and then press OK
key to select.
Enter the current Master PIN when prompted and then press OK key to
confirm. As you enter the PIN it will be shown as asterisks (*) on the
screen.
(Enter the new PIN and then press OK key to confirm. A confirmation
beep is played.)
Register your handset
IMPORTANT:
When you purchase a telephone, all handsets are already registered to
the base, so you do not need to register them. Handset registration is
only necessary when you buy extra handsets or if a handset has
become faulty.
The procedures described below are for a DET1907x handset.
They may be different if you want to register another handset model, in
which case you should refer to its user guide.
Additional handsets must be registered to the base unit before you can
use them. Up to 4 handsets can be registered to one base station.
The Master PIN is required before you can register or unregister
handsets. By default, the Master PIN is 0000.
On the base station, press and hold the HANDSET LOCATOR key for
approximately 5 seconds.
1. On the handset, press MENU key to enter menu selection.
2. Press the Navigation key to select ADVANCED SET and then press
OK key to select.
3. Press the Navigation key to select REGISTRATION and then press
OK key to select.
** If no action is taken on the handset within 10 seconds, the registration
procedure will be aborted. If this happens, repeat the first step.
Enter the Master PIN when prompted and then press OK key to confirm.
(the default master PIN is 0000)
WAITING is displayed on the screen. A confirmation beep is played to
indicate successful registration, and the handset will return to idle mode,
with its handset number displayed. ** If no base is found within a certain
period, there will be an error tone to indicate failed registration and the
handset returns to idle mode, and you will need to repeat the registration
sequence.
Unregister your handset
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select ADVANCED SET and then press
OK key to select.
3. Press the Navigation key to select UNREGISTER and then press OK
key to select.
4. Enter the Master PIN when prompted and then press OK key to
confirm. (the default master PIN is 0000)
5. Press the Navigation key to select the handset number to unregister
and then press OK key to confirm.
A confirmation beep is played to indicate successful unregistration.
** If no action is taken on the handset within 15 seconds, the
unregistration procedure will be aborted and the handset returns to idle
mode.
You must use a DET1907x handset to unregister handsets from the
DET1907x base.
Set prefix
This allows you to define a prefix number to be added to the beginning
of any predialled number, and to define a detect string to prevent the
prefix number being added unless the detect string matches the first
digits of the predialled number, in which case the prefix number will
replace the detect string digits.
You can enter up to 5 digits for the detect string and up to 10 digits for
the auto prefix number.
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select ADVANCED SET and then press
OK key to select.
3. Press the Navigation key to select AUTO PREFIX and then press OK
key to select.
4. To enter a DETECT DIGIT string, press OK key again.
The last stored detect string is displayed (if any).
Enter a detect string number (maximum 5 digits) and then press OK key
to confirm.
To enter a PREFIX number, press Navigation to display PREFIX and
then press OK key. The last stored prefix number is displayed (if any).
5. Enter the prefix number (maximum 10 digits) and then press OK key
to confirm. A confirmation beep is played.
** If no detect string (blank) is entered, the prefix number will be
automatically added to the predial number after TALK key is pressed.
For numbers starting with *, # or P, the prefix number will not be added to
the predial number after TALK key is pressed.
Change recall time
You may need the R button to send a Recall signal (also called Flash or
Timed Break Recall) if you are connected to a PBX. You should normally
leave the Recall Time at its default setting of SHORT (100ms), as this is
the standard recall required in the telephone network, but it can be
changed to MEDIUM (270ms) or LONG (600ms) if your telephone is
connected to a PBX that requires a different recall time.
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select ADVANCED SET and then press
OK key to select.
3. Press the Navigation key to select RECALL TIME and then press OK
key to select.
4. Press the Navigation key to select SHORT, MEDIUM or LONG and
then press OK key to confirm. A confirmation beep is played.
Change the dial mode (dual mode dialing version only)
You should normally leave the dialling mode at its default setting of
TONE (also called MF or DTMF).
However, you can change to PULSE if necessary.
Note: If PULSE dialling is set, you can press the * key to switch to TONE
dialling for the rest of that call.
1. Press MENU key to enter menu selection
2. Press the Navigation key to select ADVANCED SET and then press
OK key to select.
3. Press the Navigation key to select DIAL MODE and then press OK
key to select.
4. Press the Navigation key to select TONE or PULSE and then press
OK key to confirm. A confirmation beep is played.
Set first ring
When this function is set to Off, the first ring from an incoming call will
not sound. This is useful on exchanges where calling line identity is sent
after the first ring.
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select ADVANCED SET and then press
OK key to select.
3. Press the Navigation key to select FIRST RING and then press OK
key to select.
4. Press the Navigation key to select ON or OFF and then press OK key
to confirm. A confirmation beep is played.
Reset unit
You can reset your phone to its default settings with this feature.
Note: Upon reset, all your personal settings, call log and redial list
entries will be deleted and the phone will return to its default settings.
However, your phonebook will remain unchanged after reset. Also, if you
have an answering machine model, any recorded messages will remain
unchanged, but all other settings will be defaulted.
1. Press MENU key to enter menu selection.
2. Press the Navigation key to select ADVANCED SET and then press
OK key to select.
3. Press the Navigation key to select RESET and then press OK key to
select.
4. Press OK key again to confirm. A confirmation beep is played and the
unit is reset to its default settings.
Answering machine settings
Set ring delay
1. Press the MENU key to enter menu selection.
2. Press the Navigation key to select ANSW MACHINE and then press
OK key to select.
3. Press the Navigation key to select SETTINGS and then press OK key
to select.
4. Press OK key to enter the RING DELAY option list.
5. Press the Navigation key to select 2 - 7 RINGS or ECONOMY and
then press OK key to confirm your choice.
6. A confirmation beep is played. Press HANG-UP/EXIT key to go back
to idle mode.
* If you select Economy mode, the answering machine will answer calls
and start playing the greeting message after 5 rings if you have no new
messages, or after 3 rings if there is at least one new message
recorded.
To activate/deactivate remote control access
1. Press the MENU key to enter menu selection.
2. Press the Navigation key to select ANSW MACHINE and then press
OK key to select.
3. Press the Navigation key to select SETTINGS and then press OK key
to select.
4. Press the Navigation key to select REMOTE ACC. and then press OK
key to select.
5. Press the Navigation key to select ACTIVATE or DEACTIVATE and
then press OK key to confirm.
6. A confirmation beep is played. Press HANG-UP/EXIT key to go back
to idle mode.
* Once the remote control access is activated, you can check the
messages of your answering machine when you are away from home,
by calling from another phone.
* If the answering machine is turned off, you must change your master
PIN from its default 0000, before you can use the remote access feature.
To check messages remotely
1. When you are away from home, dial your home phone number from
another phone. The answering machine answers and starts playing your
greeting message.
2. While the OGM is playing, press # key on the phone you used to dial
and enter the remote access code (which is the same as your master
PIN code).
* The answer machine will drop the line immediately if there is no
detection of the master PIN entry within 8 seconds from pressing the #.
* If the remote access code is correct, a confirmation beep can be
heard, and then you need to press the 2 key, within 8 seconds, to start
playing any messages.
The remote feature lets you perform the following functions:
To Press this button
Review message 1
Play back messages 2
Stop message playback 8
Erase message 6 (during message playback)
Skip message 3
Turn on answerer machine 7
Turn off answerer machine 9
* If the answering machine is off, and the master PIN has been changed
from its default 0000, it will answer the call after 10 rings. Dial the master
PIN code within 8 seconds and you will hear a beep to confirm you have
entered the remote access mode, as above.
Set the OGM voice language
1. Press the MENU key to enter menu selection.
2. Press the Navigation key to select ANSW MACHINE and then press
OK key to select.
3. Press the Navigation key to select SETTINGS and then press OK key
to select.
4. Press the Navigation key to select LANGUAGE and then press OK
key to select.
5. Press the Navigation key to select your preferred language and then
press OK key to confirm.
6. A confirmation beep is played. Press HANG-UP/EXIT key to go back
to idle mode.
Call screening
Call screening allows you to hear the caller while he is leaving a
message. You can then decide if you want to talk to the caller directly. To
adjust the speaker’s volume during call screening, press + and - keys on
the base station. The lowest volume level turns call screening off.
In Case of Problems
Service Hotline
Should problems arise with the telephone, please refer to the following
information first. In the case of technical problems, you can contact our
hotline service, Tel. 0900 00 1675 within Switzerland (Swisscom fees at
time of going to print: CHF 2.60/min). In the case of claims under the
terms of guarantee, please contact your sales outlet. There is a 2 year
period of guarantee.
Problems and solutions
Problems Solutions
No connection to
base station
possible
- Check that the handset has been registered
on the base station with the correct PIN code.
No telephone calls
possible
- The telephone is not connected properly or is
defective. Only use the telephone connection
cable supplied.
- Test whether the telephone connection is in
order by using another telephone.
- The power adaptor plug is not plugged in or
there is a complete power failure.
- The rechargeable batteries are empty or
defective.
- The handset is too far from the base station.
- The wrong dialling mode is set.
Connection is
disturbed or cut off
- The handset is too far from the base station.
- The base station is in an unsuitable location.
The system no
longer responds
- Reset all the functions to their default settings.
- Disconnect the power adapter plug briefly from
the power socket.
The batteries are
empty within a
short time
- The batteries are empty or defective.
- Place the handset in the base station properly.
Clean the contact surfaces on the handset and
base station with a soft, dry cloth.
- Place the handset in the base station for
16 hours.
The caller number
display (CLIP)
does not function
- The caller number display (CLIP) is a
supplementary service offered by your
telephone network provider. Contact your
network provider for further information.
- The caller has suppressed the transmission of
their phone number.
The answering
machine does not
record any
messages
- Check whether the answering machine
memory is full. Delete messages from the
memory, if necessary.
Remote access is
not possible
- Check that the correct security code has been
entered for remote access.
- The telephone used for remote access must
be set to tone dialling.
Declaration of Conformity
This device fulfils the requirements stipulated in the EU
directive: 1999/5/EC directive on radio equipment and
telecommunications terminal equipment and the mutual recognition of
their conformity. Conformity with the above mentioned directive is
confirmed by the CE mark on the device.To view the complete
Declaration of Conformity, please refer to the free download available on
our web site at www.switel.com.
Maintenance / Guarantee
Maintenance
- Clean the housing surfaces with a soft, fluff-free cloth.
- Do not use any cleaning agents or solvents.
Guarantee
SWITEL equipment is produced and tested according to the latest
production methods. The implementation of carefully chosen materials
and highly developed technologies ensure trouble-free functioning and a
long service life. The terms of guarantee do not apply where the cause
of equipment malfunction is the fault of the telephone network operator
or any interposed private branch extension system. The terms of
guarantee do not apply to the batteries or power packs used in the
products. The period of guarantee is 24 months from the date of
purchase.All deficiencies related to material or manufacturing errors
within the period of guarantee will be redressed free of charge. Rights to
claims under the terms of guarantee are annulled following tampering by
the purchaser or third parties. Damage caused as the result of improper
handling or operation, normal wear and tear, incorrect positioning or
storage, improper connection or installation or Acts of God and other
external influences are excluded from the terms of guarantee. In the
case of complaints, we reserve the right to repair defect parts, replace
them or replace the entire device. Replaced parts or devices become
our property. Rights to compensation in the case of damage are
excluded where there is no evidence of intent or gross negligence by the
manufacturer.If your device does show signs of a defect within the
period of guarantee, please contact the sales outlet where you
purchased the SWITEL device, producing the purchase receipt as
evidence. All claims under the terms of guarantee in accordance with
this agreement can only be asserted at the sales outlet. No claims under
the terms of guarantee can be asserted after a period of two years from
the date of purchase and hand-over of the product.
Disposal
In order to dispose of your device, take it to a collection point
provided by your local public waste authorities (e.g. recycling
centre). According to laws on the disposal of electronic and
electrical devices, owners are obliged to dispose of old electronic
and electrical devices in a separate waste container. The symbol
indicates that the device must not be disposed of in normal
domestic waste!
Batteries represent a hazard to health and the
environment!
Never open, damage or swallow batteries or allow them to pollute the
environment. They may contain toxic, ecologically hazardous heavy
metals. You are legally obliged to dispose of power packs and batteries
at the point of sale or in the corresponding containers at collection points
provided by local public waste authorities. Disposal is free of charge.
The symbols indicate that the batteries must not be disposed of in
normal domestic waste and that they must be brought to collection
points provided by local public waste authorities.
Packaging materials must be disposed of according to local
regulations.
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Switel DET19073 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Switel DET19073

Switel DET19073 Bedienungsanleitung - Deutsch - 2 seiten

Switel DET19073 Bedienungsanleitung - Französisch - 2 seiten

Switel DET19073 Bedienungsanleitung - Italienisch - 2 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info