Bedienungsanleitung Switel TF535 (Seite 20 von 22) (Deutsch, Englisch, Französisch, Italienisch)

687680

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Connecting the handset

After unpacking your telephone, you must first

connect the telephone receiver to the base unit.

The spiral cable needed for this has two identical

connections so that there can be no confusion. First

take one end of the spiral cable and plug it into the

socket at the bottom of the receiver. Now plug the

other end into the socket on the left hand side of the

base unit.

Insert battery

Before connecting your new telephone to the

telephone network, the supplied battery should be

installed. Please always use a type AA 1.5V

alkaline battery. The battery is required for the

display and other features of the telephone. Before

installing or changing the battery make sure that the

telephone is not connected to the telephone

network. The battery compartment is to be found on

the underside of your telephone.

1. Open the battery compartment with a small

screwdriver or a pointed object.

2. Insert the battery. Ensure that the polarity is

correct. Push the "−" pole onto the small spring

and then press the "+" pole downwards.

3. Close the battery compartment.

Note: The battery must be changed when the

display is no longer visible. Disconnect the

telephone line cord before installing or replacing the

battery.

Hearing aid compatible

The telephone has a special circuit working on the

basis of induction for transmitting speech to hearing

aids. Please set your hearing aid to "T".

Setting the clock

The present time is shown in the display. To set the

clock, please proceed as follows:

1. Press the SET button (3) beneath the display

once. The hours figure in the display starts to

flash.

2. Press the +/− button (2) until you see the present

hour in the display.

3. Press the SET button again and the minutes

figure in the display starts to flash.

4. Enter the present number of minutes by

repeatedly pressing the +/- button.

5. The setting of the time is completed by pressing

the SET button.

OPERATION

Using the telephone

1. Lift the receiver and wait until you hear the

dialing tone.

2. Now dial the required telephone number. The

number dialed will be shown in the display. The

display shows a telephone number with a

maximum of 16 digits. If the number dialed is

longer, only the last 16 digits will be displayed.

3. To end the call, simply replace the receiver.

Receiving calls

As soon as you receive a call you will hear the

ringing tone and the visual call indicator will come

on at each ring. The call can now be accepted by

lifting the receiver.

Increasing the volume of the receiver

If the caller’s voice should ever be too quiet, you

can increase the volume of the receiver with the

slide switch

(14) during the call.

NOTE: The changed volume setting is not saved

and must be increased again for the next call if

required.

Redial

If a connection that you have dialed is engaged or

you were unable to get through, simply replace the

receiver. The last number dialed remains stored in

the telephone automatically.

To use the redial facility, lift the receiver and press

the redial button (11).The stored redial number

will now be dialed.

Call duration display

After dialing the telephone number, the current call

duration in minutes and seconds will be shown in

the display after a few seconds.

You can also use the internal clock as a stopwatch.

To do this, press the button (4) with the receiver

on the hook or during a call. The time measurement

will be stopped using the same button . The

measured time will still be shown in the display for a

few seconds and the display then jumps back to

showing the present time.

Adjustable ringing tone

By means of the slide switches “Ringer”

(16) and “Tone” (15) on the right hand

side of your telephone you can choose the settings

to match your requirements. If at any time you do

not want to be disturbed, use the "OFF" setting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Switel TF535 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info