Bedienungsanleitung Sylvania 6842PE (Seite 8 von 28) (Englisch)

11995

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

PERATING THE PLASMA DISPLAY

BASIC OPERATIONS

The following is a simple explanation of the pro-

cedure for turning the power of the display ON or

in STANDBY, and the procedure for selecting the

input signal.

The procedure described here is for the remote

control, however the POWER, INPUT SELECT

and VOLUME buttons on the plasma display can

also be used in the same way.

1 Press the POWER button.

Confirm that the STANDBY indicator is lit

before pressing the POWER button.

The power turns ON and the ON indicator on

the main unit lights up. The STANDBY indica-

tor on the main unit disappears.

NOTE:

• It takes approximately 8 seconds for the screen to

display after turning the power ON, but this is not

a malfunction.

Select the input signal by pressing the INPUT

SELECT button.

Each time you switch the input, the name of

the selected input terminal is displayed on the

screen for approximately 4 seconds.

NOTE:

• "No signal" is displayed on the screen if there is

no input from the selected terminal and there is

no message currently displayed on the screen for

volume adjustment or the setup menu, etc.

• If there is no video signal and there has been no

operation from the remote control or the buttons

on the main unit for more than 15 minutes, the

auto shut-off function activates and the display

switches to standby mode.

POWER

INPUT SELECT

DISPLAY

VOL

MUTE

SCREEN MODE

STILL

POWER

INPUT SELECT

3 Adjust the volume and screen size according

to your requirements.

Perform adjustments to the volume (VOL

button), screen aspect ratio (SCREEN MODE

button), and picture settings (MENU button)

NOTE:

• When you adjust the volume with the VOL

button, a message such as the following is dis-

played on the screen. This message disappears

approximately 4 seconds after performing adjust-

ments.

• If you turn the audio mute on, a message slowly

flashes on the screen. At this time, if you press

another button, this flashing stops.

•To turn the audio mute off, either press the MUTE

button again or press the VOL

button.

• If you press either the PREVIOUS,

, B or {

button in a mode apart from the image adjustment

mode. A message such as the following is dis-

played.

4 Press the POWER button to turn the power

STANDBY.

The ON indicator on the main unit disappears

and the STANDBY indicator lights up.

NOTE:

•You cannot turn the power ON for approximately 3

seconds after the power enters the standby mode.

Do not turn the power STANDBY and then ON

again in a short time interval.

•Even if the power is turned STANDBY, the main

unit is in the standby mode. In order to shut the

main power of the display OFF, it is necessary to

remove the AC cord from the power outlet.

L0601(EN)v1.qx3 04.8.10 3:08 PM Page 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sylvania 6842PE Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info