Bedienungsanleitung Sym DD (Seite 14 von 24) (Englisch)

517188

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

10.INSPECTION AND MAINTENANCE BEFORE RIDING

Replenishment:

1. Using the main stand to support the vehicle on a level ground, lift up the saddle, and remove the oil tank

cover.

2. Turn the oil tank cap to the left to remove. Add oil until reaches to the standard level.

3. Screw in the oil tank cap until properly tightened, then reinstall the tank cover and lower the saddle and

press it down until locked.

Add oil note:

z Use only 2-cycle engine oil meeting Japanese Automobile Standard Organization FC specifications.

Otherwise, this company will not assume any responsibility for damages resulted from using

substandard engine oil.

z When adding oil, do not let foreign materials, dust, dirt enter into the oil system, do not use different

brands mixed oil, because this will affect the engine’s performance.

z Do not add oil above the standard level. Clean spilled oil around the oil tank cap.

z Be sure to tighten the oil tank cap properly after adding oil.

INSPECTION OF FUEL LEVEL

z Firmly support the scooter with its main stand on a leveled ground, turn the main switch to “ON” position,

check if the fuel meter needle moves.

z Fuel gauge may be defective or electric circuit disconnected if there is some fuel in the tank, but the

needle does not move. Please drive slowly to an authorized service station to have your scooter

checked.

Note: It is not necessary to start engine to check the fuel level.

TRANSMISSION OIL INSPECTION AND CHANGE

Inspection:

z Use the main stand to support the scooter on a level ground, after the engine stops, wait for 3~5

minutes. Remove the bolt for transmission oil access hole, and check if transmission oil reaches the

lower edge of check screw hole (same as the access hole).

z Add oil until oil flows out from the check screw hole if oil level is under the lower edge of check screw

hole.

Oil change:

z Use the main stand to support the scooter on a level ground. Remove the bolt for transmission oil

access hole and oil drain bolt, and drain out the oil.

z Install the oil drain bolt and tighten it securely. Fill transmission oil through the access hole until oil

reaches the lower edge (when oil flows out). Install the bolt and tighten it securely. (Make sure that

the bolt had been tightened securely after adding oil, and check for oil leakage.)

※ Recommended Oil: Genuine SYM HYPOID GEAR OIL (SAE 85W-140)

INSPECTION AND ADJUSTMENT OF BRAKE FREE PLAY

INSPECTION: (Brake lever free play must be checked with the engine shut off.)

z Brake lever free play for front and rear wheels

When checking the hand-braking lever for front

and rear wheels, its free play (the stroke of

hand-braking lever from no braking to initial

braking) should be 10~20mm.

It is abnormal if the feel is spongy when holding

the hand-braking lever forcefully.

10~20mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sym DD Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info