Bedienungsanleitung Sym FIDDLE III 200i (Seite 19 von 27) (Englisch)

660399

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

§CHECKING AND CHANGING FUSES §

Fuse box is on the frame body, remove the luggage box then you can see the fuse box is on the frame

body right side and it is near start magnetic switch. Turn off ignition switch, and check fuses if they are

intact. Replace the blown fuse with a new one having the same specified amperage rating (10A or

7.5A ). Using a fuse which the amperes is larger than specification, a brass or iron wire to replace a

blown fuse is strictly prohibited to avoid damaging the electrical system and the circuit.

 Remove the storage box, and you’ll find the fuse holder near battery.

 Open the fuse box cover, and pull out the fuse. Check it for damage or broken.

 Fuses must be firmly secured with wire connectors when replacing. Loose connections will result

in overhead and damage.

 Use only parts having the specified specification to replace electrical components such as light

bulbs. Using parts not having the specified specifications for replacement may cause the fuse

to blow and over-discharge the battery.

 Avoid spraying water directly on or around fuse box when washing the motorcycle.

 If the new fuse burn out quickly again, please check the faulty reason before replace it again.

Take your motorcycle to your dealer for an inspection if a fuse is blown by unknown causes.

§CHECKING THE TURN SIGNAL LIGHTS AND HORN §

 Turn the ignition switch key to the “ON” position.

 Turn on the turn signal light switch, and make sure that the front & rear and left & right signal

lights flashes and also check if the warning buzzer sounds.

 Check turn signal light covers if they are dirty, crack, or loosen.

 Press horn button to check if it works.

§CHECKING THE FRONT AND REAR LIGHTS §

 Start engine and turn on the head lamp switch. Check if head lamp and rear lamp come on.

 Check the brightness and direction of front light by wall to see if it is correct.

 Check the head lamp cover if it is dirty, crack, or loosen.

§CHECKING THE BRAKE LIGHT §

 Turn the ignition switch key to the “ON” position, hold the hand-braking levers for front and rear

wheels. Check if the brake lights come on.

 Check the brake light cover if it is dirty, crack, or loosen.

CAUTION:

 Specified specification bulbs should be used for turn signal lights. Otherwise, the normal

operation of turn signal lights will be affected.

 Turn on the turn signal light before turning or switching lane to warn driver of vehicles behind.

 Turn off the turn signal light immediately by pressing its button down after using. Otherwise,

the flashing of twin signal lights may confuse the drivers of vehicles behind.

CAUTION:

 Use only specified specification bulbs, do not use bulbs with different specifications to avoid

damaging electrical system, burning out bulbs, and discharging the battery.

 Do not modify or add other electrical components to prevent over load or short circuit which

may result in a fire and burn down the motorcycle in serious cases.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sym FIDDLE III 200i Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info