Bedienungsanleitung Sym Mio 115 - FS11W1 (Seite 8 von 28) (Englisch)

673291

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

7. Use of Each Component

 Speedometer：

Indicates riding speed there are two type of unit (Km/h) or (mph).

 LCD monitor (Including Odometer)：

Press “MODE” to switch showing the total mileage/ short mileage/ oil use.

Press “SET” to switch showing the battery voltage/ time.

 High Beam Indicator：

This indicator comes on with high beam headlight is turned on.

 Turn Signal Indicator：

The left or right Indicator will be flashing according to the operated directions of turn signal light switch

when it is turned on.

 Fuel Gauge：

The pointer in this gauge shows how much fuel remains in the tank.

If the pointer stays in “E” position when key switch is turned to “ON”, please fill up with gasoline (over 92

Unleaded gasoline)

 EFi trouble warning indicator：

When turn the main switch to “ON”, this warning indicator will come on and then go off after the

engine is running. It displays the condition of the EFi system is working correctly. If there is any

problem on the EFi system, the warning indicator will remain on all the time or does not come on.

Please contact with a SYM dealer to check the self-diagnosis system or electrical connections.

 Engine Oil Change Indicator：

This indicator shows when to change engine oil by light. Usually, the scooter has been ride

approximately 1,000 km, the indicator will show its light. Then, it means you should change or add the

engine oil, and turn the mileage to “0” in the OIL mode. After replacing it, please turn to KEY ON. Press

the “SET” 2 times in the “OIL” mode, let the indicator’s light be off, and turn the mileage to “0” in the OIL

mode.

Notice: 1. Please change oil when the initial 300 km, then change every 1,000 km.

2. If your motor’s mileage has already been exceeded the kilometers, but the light does not show,

please go to the SBC/ dealer store for check.

Display mode switch:

1. When the key switch is turned to “ON” in “TOTAL” mode, Press “MODE” button within 1 second to

change between “TOTAL” , “OIL” and ”TRIP” modes.

2. The “TOTAL” means the total mileage of the motor, cannot be reset. But in “TRIP” mode, and press the

SET“ over 2 seconds, then the mileage can be erased and newly calculated.

3. Under “CLOCK” mode, press “SET” 1 second, will switch to “VOLTAGE” showing.

Time setting

1. Showing the 24 hour mode time (

0:00~23:59). Time allows ±2 seconds tolerance.

2. When the key switch is turned to “ON,” the clock will show the 24 hour mode hour/ minute .

3. Under the “CLOCK” mode, press “ MODE” button (over 2 seconds) to enter “TIME” setup mode,

Then press “MODE” 1 second, then you could switch setup mode (as below):

HOUR MIN(10min) MIN(1min)

2. Under time setting mode, press “SET” button shortly to increase the readings. The number will

increase 1 at one time, it will automatically leave the setup mode if you do not take action within

30 seconds.

TOTAL

CLOCK

TRIP

CLOCK

OIL

CLOCK

OIL

VOLTAGE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sym Mio 115 - FS11W1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info