6987
19
Zoom out
Zoom in
Vorherige Seite
1/25
Nächste Seite
8. INSPECTION AND MAINTENANCE BEFORE RIDING
19
CHECKING AND CHANGING FUSES
Turn off ignition switch, and check fuses if they are intact. Replace the blown fuse with a new one
having the same specified amperage rating (7A). Using a fuse of more than 7 amperes, a brass or iron
ire to replace a blown fuse is strictly prohibited to avoid damaging the electrical system and the circuit.
Remove the storage box, and you’ll find the fuse box near light.
Open the fuse box cover, and pull out the fuse. Check it for damage or broken.
Fuses must be firmly secured with wire connectors when replacing. Loose connections will result in
overhead and damage.
Use only parts having the specified specification to replace electrical components such as light bulbs.
Using parts not having the specified specifications for replacement may cause the fuse to blow and
over-discharge the battery.
Avoid spraying water directly on or around fuse box when washing the scooter.
Take your scooter to your dealer for an inspection if a fuse is blown by unknown causes.
REMOVE INSTALLATION
CHECKING THE SPARK PLUG
Remove the cap of spark plug cable (remove
the spark plug using the spark plug wrench in
the tool kit.
Check the electrode if it is dirty or fouled by
carbon deposits.
Remove the carbon deposits on the electrode
with steel wire, and clean the spark plug with
gasoline, then, wipe dry with a rag.
Check the electrode, and adjust its gap to
0.6~0.7 mm. (Check it with a feeler gauge)
Hand tight the spark plug as far as it can go
and then tighten it another 1/2~3/4 turns with
a wrench.
WARNING
The engine is very hot after running. Pay attention not to get burned.
Use only spark plugs suitable for the engine specifications of this scooter recommended by the
manufacturer. (Refer to specifications.)
CHECKING THE FRONT AND REAR LIGHTS
Start engine and turn on the head lamp switch. Check if head lamp and rear lamp come on.
Check the brightness and direction of front light by wall to see if it is correct.
Check the head lamp cover if it is dirty, crack, or loosen.
0.6~0.7 mm
Press in from above
Fuse connectors
Wire
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sym Mio wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Sym Mio

Sym Mio Bedienungsanleitung - Holländisch - 20 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info