Bedienungsanleitung Sym SYMPHONY SR 50 (Seite 19 von 24) (Englisch)

660406

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

§CHECKING AND CHANGING FUSES §

Turn off ignition switch, and check fuses if they are intact. Replace the blown fuse with a new one having the

same specified amperage rating (10A&15A). Using a fuse of more than (10A or 15A) amperes, a brass or iron

wire to replace a blown fuse is strictly prohibited to avoid damaging the electrical system and the circuit.

 Remove the storage box, and you’ll find the fuse holder near battery.

 Open the fuse box cover, and pull out the fuse. Check it for damage or broken.

 Fuses must be firmly secured with wire connectors when replacing. Loose connections will result in

overhead and damage.

 Use only parts having the specified specification to replace electrical components such as light bulbs.

Using parts not having the specified specifications for replacement may cause the fuse to blow and

over-discharge the battery.

 Avoid spraying water directly on or around fuse box when washing the scooter.

 If the new fuse burn out quickly again, please check the faulty reason before replace it again. Take your

scooter to your dealer for an inspection if a fuse is blown by unknown causes.

§CHECKING THE TURN SIGNAL LIGHTS AND HORN §

 Turn the ignition switch key to the “ON” position.

 Turn on the turn signal light switch, and make sure that the front & rear and left & right signal lights flashes

and also check if the warning buzzer sounds.

 Check turn signal light covers if they are dirty, crack, or loosen.

 Press horn button to check if it works.

§CHECKING THE FRONT AND REAR LIGHTS §

 Start engine and turn on the head lamp switch. Check if head lamp and rear lamp come on.

 Check the brightness and direction of front light by wall to see if it is correct.

 Check the head lamp cover if it is dirty, crack, or loosen.

§CHECKING THE BRAKE LIGHT §

 Turn the ignition switch key to the “ON” position, hold the hand-braking levers for front and rear wheels.

Check if the brake lights come on.

 Check the brake light cover if it is dirty, crack, or loosen.

CAUTION:

 Specified specification bulbs should be used for turn signal lights. Otherwise, the normal operation of

turn signal lights will be affected.

 Turn on the turn signal light before turning or switching lane to warn driver of vehicles behind.

 Turn off the turn signal light immediately by pressing its button down after using. Otherwise, the

flashing of twin signal lights may confuse the drivers of vehicles behind.

CAUTION:

 Use only specified specification bulbs, do not use bulbs with different specifications to avoid damaging

electrical system, burning out bulbs, and discharging the battery.

 Do not modify or add other electrical components to prevent over load or short circuit which may result

in a fire and burn down the motorcycle in serious cases.

【INSTALLATION】

Press in from above

【REMOVE】

Wire

Fuse connectors

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sym SYMPHONY SR 50 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info