540608
4
Zoom out
Zoom in
Vorherige Seite
1/27
Nächste Seite
6 7
1
2
3
1
2
3
EN
NL
DE
JP
IT
ES
FR
CH
The accuracy of the Flow's power display depends on factors such as the pressure of the cylinder
against the tyre, the tyre pressure, fluctuating magnetic forces and the difference in mains voltage.
To guarantee a good power measurement, the brake must be calibrated. For optimal calibration
we recommend cycling at least 3 minutes beforehand to warm-up the brake. Make sure the tyre
pressureisbetween7and8bar.
Brake calibration
The calibration value 0 appears at the bottom. You start the brake calibration with the Up arrow,
whichcausesthreedashestoappearatthebottomofthedisplay.Cycleataspeedabove30km/h
(or19mi/h)untilthewordSTOPappears.Themomentyoustop,theFlowcomputermeasuresthe
deceleration of the rear wheel and the new calibration value appears on the display.
If the calibration fails (e.g. because you began pedalling during the measurement), ERROR appears on the display.
You can start the calibration again with the Up arrow. You can set the calibration value to 0 with the Down arrow.
Use MODE to confirm the settings and switch to the training display.
Settings before you begin
The Flow registers four training parameters: speed, power, cadence and heart rate.
Two training parameters are shown at any time, on the 2nd and 3rd lines of the display. With the
Up arrow you can switch the 2nd line from speed to cadence, power and heart rate. With the
Down arrow you can switch the training parameters on the 3rd line.
MODE functions for SPEED (km/h or mi/h)
The MODE functions on the 1st line of the display correspond to the training parameter on the 2nd
line. When the 2nd line is set to speed, the MODE key switches between ETM (elapsed time), TRP
(trip time), ODO (odometer), MAX (maximum speed) and AVS (average speed).
The values only reflect the actual time spend cycling since the computer was reset or switched on. If you take a
break, the data will be retained. Once you resume cycling, the computer begins calculating again, using all the data.
MODE functions for CADENCE (Cad)
When the 2nd line is set to cadence (Cad), TRP means the total number of pedal revolutions during
thetrip,MAXmeansthemaximumpedallingfrequencyandAVStheaveragepedallingfrequency.
Training with the Flow
ETM TRP ODO MAX AVS
MODE
ETM TRP MAX AVS
MODE
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tacx Flow computer wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info