Bedienungsanleitung Tamaha RP-U200 (Seite 32 von 57) (Englisch)

98206

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

E-28

APPENDIX

Problem

The unit cannot be turned on

though the power switch is

pressed.

No sound.

No sound from the surround

speakers

No sound from the center speaker

No sound field effect.

No effect of Dolby Digital or DTS

though the sound field program

“NORMAL” is selected.

Cause

The power cord is not plugged in or is not

completely inserted.

This unit is in the standby mode.

Incorrect output cord connections.

The muting function of this unit is on.

Headphones are connected to the headphone

jack of this unit.

The volume is set to minimum.

The playback source is not selected by the

input selector keys.

The power of the equipment selected as the input

source is off.

The output level of the surround speakers is

set to minimum.

The DSP is off.

Under “Speaker Settings” in the SETUP panel

of the Application, the check box “Use the

surround speakers” is not checked.

The output level of the center speaker is set to

minimum.

The DSP is off, or a Hi-Fi DSP program is

selected.

Under “Speaker Settings” in the SETUP panel

of the Application, the check box “Use the

center speaker” is not checked.

The source does not contain center channel

sound signals.

The DSP is off.

The playback source is encoded with neither

Dolby Digital nor DTS.

Remedy

Firmly plug in the power cord.

Turn on this unit by pressing the power switch on the

front panel or the POWER key on the remote control.

Connect the cords properly. If the problem

persists, the cords may be defective.

Turn off the muting by pressing the MUTE key.

Disconnect the headphones from the

headphone jack to output sound from the

speakers.

Increase the volume.

Select the playback source using the input

selector keys.

When PC is selected as the input source, check

that the USB, digital or analog input is correctly

selected.

Turn on the equipment.

Increase the output level of the surround

speakers by using the test tone. (Refer to page 19

on how to adjust the speaker output levels.)

Turn on the DSP and select an appropriate

sound field program.

Check the check box “Use the surround

speakers”.

Increase the output level of the center speaker

by using the test tone. (Refer to page 19 on how

to adjust the speaker output level.)

Turn on the DSP and select a CINEMA DSP

program.

Check the check box “Use the center speaker”.

Use a source which contains center

channesound signals.

Turn on the DSP.

Use a source encoded with Dolby Digital or DTS.

Troubleshooting

Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or if the

instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer or service

center.

APPENDIX

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tamaha RP-U200 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Tamaha RP-U200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info