Bedienungsanleitung Tanaka TCS33EDP (Seite 11 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

816446

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

English

ASSEMBLY PROCEDURES

WARNING

Switch oﬀ the engine before carrying out any checks or

maintenance.

Never try to start engine without side case, guide bar and chain

securely fastened.

1. Pull the front hand guard (2) toward the front handle to check that

the chain brake is disengaged. (Fig. 2)

2. Remove guide bar clamp nuts (3). Remove the side case (4).

(Fig. 3)

* In case of installing the spiked bumper (5), install the spiked

bumper (5) to the unit with two screws. (Fig. 4)

3. Install the guide bar (6) onto the bolts (7), then push it toward the

sprocket (8) as far as it will go. (Fig. 5)

4. Conﬁ rm the direction of saw chain (9) is correct as in the ﬁ gure,

and align the chain on the sprocket (8). (Fig. 5)

5. Guide the chain drive links into the bar groove all around the

guide bar (6).

6. Install the side case (4) onto the bolts (7).

Make sure that the boss of chain tension adjust bolt (10) ﬁ ts into

the hole of the guide bar (11). (Fig. 5)

Then tighten the guide bar clamp nuts (3) by hand that allows the

guide bar end to move up and down easily. (Fig. 6)

7. Raise the guide bar end, and tighten the chain (9) by turning the

tension adjustment bolt (12) clockwise. To check proper tension,

lightly lift up the center of chain and there should be about 0 –

0.5

mm clearance between guide bar (6) and edge of drive link

(13). (Fig. 7, 8)

CAUTION

PROPER TENSION IS EXTREMELY IMPORTANT

8. Raise the guide bar end and securely tighten the guide bar

clamp nuts (3) with the combi box spanner (14). (Fig. 9)

9. A new chain will stretch so adjust the chain after a few cuts and

watch chain tension carefully for the ﬁ rst half hour of cutting.

NOTE

Check the chain tension frequently for optimum performance

and durability.

CAUTION

○ When the chain is excessively tightened, the guide bar and

chain will be damaged rapidly. Conversely, when the chain is

excessively loosened, it may get out of the groove in the guide

bar.

○ Always wear gloves when touching the chain.

WARNING

During operation, hold chain saw ﬁ rmly with both hands. A single

hand operation may cause serious injury.

OPERATING PROCEDURES

Fuel (Fig. 10)

WARNING

○ The chain saw is equipped with a two-stroke engine. Always

run the engine on fuel, which is mixed with oil. Provide good

ventilation, when fueling or handling fuel.

○ Fuel is highly ﬂ ammable and it is possible to get seriously injured

when inhaling or spilling on your body.

Always pay attention when handling fuel. Always have good

ventilation when handling fuel inside building.

Fuel

○ Always use branded 89 octane unleaded gasoline.

○ Use genuine two-cycle oil or use a mix between 25:1 to 50:1,

please consult the oil bottle for the ratio or Tanaka dealer.

○ If genuine oil is not available, use an anti-oxidant added quality

oil expressly labeled for air-cooled 2-cycle engine use (JASO

FC GRADE OIL or ISO EGC GRADE). Do not use BIA or TCW

(2-stroke water-cooling type) mixed oil.

○ Never use multi-grade oil (10 W/30) or waste oil.

○ Never mix fuel and oil in machine’s fuel tank. Always mix fuel and

oil in a separate clean container.

Always start by ﬁ lling half the amount of gasoline, which is to be

used.

Then add the whole amount of oil. Mix (shake) the fuel mixture. Add

the remaining amount of gasoline.

Mix (shake) the fuel-mix thoroughly before ﬁ lling the fuel tank.

Mixing amount of two-cycle oil and gasoline

Gasoline (Liter) Two-cycle oil (ml)

Ratio 50:1 Ratio 25:1

0.5 10 ——— 20

1 20 ——— 40

2 40 ——— 80

4 80 ——— 160

Fueling (Fig. 11)

WARNING

○ Always shut oﬀ the engine and let it cool for a few minutes before

refueling.

Do not smoke or bring ﬂ ames or sparks near the fueling site.

○ Slowly open the fuel tank (15), when ﬁ lling up with fuel, so that

possible overpressure disappears.

○ Tighten the fuel tank cap carefully, after fueling.

○ Always move the unit at least 3 m from the fueling area before

starting.

○ Always wash any spilled fuel from clothing immediately with

soap.

○ Be sure to check any fuel leaking after refueling.

Before fueling, clean the tank cap area carefully, to ensure that no

dirt falls into the tank. Make sure that the fuel is well mixed by shaking

the container, before fueling.

Chain oil (Fig. 11)

WARNING

Never use waste or regenerated oil. If you use them, it will cause

damage to your health or this unit.

Slowly open the oil tank (16), and ﬁ ll up with chain oil. Always use

high quality chain oil. When the engine is running, the chain oil is

automatically discharged.

Fill up the oil tank (16) with chain oil every time when refueling.

NOTE

When pouring fuel or chain oil into the tank, place the unit with

cap side up. (Fig. 11)

ADJUSTMENT OF CHAIN OIL SUPPLY

The chain oil quantity discharged through the lubrication system

is adjusted to the maximum in the factory. Adjust the quantity in

accordance with the operating condition.

Turn the adjusting screw (17) counterclockwise to increase the

quantity and turn it clockwise to decrease the quantity. (Fig. 12)

Chain brake operation (Fig. 2, 13)

Chain brake is designed to activate in an emergency such as kick-

back action.

Application of brake is made by moving the front hand guard (2)

towards the guide bar. During the chain brake operation, even if

the throttle lever is pulled, the engine speed does not increase and

the chain does not turn. To release the brake, pull up the front hand

guard (2) toward the front handle.

If the engine keeps rotating at high speed with the brake engaged,

the clutch will overheat causing trouble.

When the brake engages during operation, immediately release the

throttle lever to slow down the engine.

How to conﬁ rm the activation of the chain brake (Fig. 14)

1) Turn oﬀ the engine.

2) Holding the chain saw horizontally, release your hand from the

front handle, hit the tip of the guide bar to a stump or a piece

of wood, and conﬁ rm brake operation. Operating level varies by

bar size.

000BookTCS33EDPWE.indb11000BookTCS33EDPWE.indb11 2019/01/2415:24:222019/01/2415:24:22

Tanaka TCS33EDP Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info