Bedienungsanleitung Tanaka TRB24EAP-TA (Seite 5 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

571112

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

MODEL TRB24EAP / TRB24EA

Engine Size (ml) 23.9

Spark Plug NGK BMR7A

Dry weight (kg) 3.9

Fuel tank capacity (l) 0.52

Sound pressure level

LpA (dB (A))

by ISO22868

Uncertainty

(dB (A))

By ANSI 69*

By CEN 87*

1.8*

Sound power level

Lw measured (dB (A))

by ISO22868

Sound power

level LwA (dB (A))

by 2000/14/EC

107*

109*

Vibration level (m/s

)

by ISO22867

Uncertainty

(

m/s

)

1.0

*1: Equivalent noise level/vibration level are calculated as the time-

weighted energy total for noise/vibration levels under various

working conditions with the following time distribution: 1/7 Idle,

6/7 racing.

*2: ANSI B175.2

* All data subject to change without notice.

ASSEMBLY PROCEDURES

Blow pipes to main body (Fig. 1)

Inspect the main body and accessories.

Connect straight pipe (1) securely. Align projection (2) in straight

pipe with groove (3) on blower housing and slide the pipe into the

blower housing.

Rotate the pipe clockwise to lock it into place.

Conic pipe to straight pipe (Fig. 2)

○ Align groove (5) on the conic pipe (6) and projection (4) on

straight pipe (1) and rotate the conic pipe in place.

OPERATING PROCEDURES

Fuel (Fig. 3)

WARNING

○ The unit/machine is equipped with a two-stroke engine. Always

run the engine on fuel, which is mixed with oil.

Provide good ventilation, when fueling or handling fuel.

○ Fuel contains highly ﬂ ammable and it is possible to get the

serious personal injury when inhaling or spilling on your body.

Always pay attention when handling fuel. Always have good

ventilation when handling fuel inside building.

Fuel

○ Always use branded 89 octane unleaded gasoline.

○ Use genuine two-cycle oil or use a mix between 25:1 to 50:1,

please consult the oil bottle for the ratio or Tanaka dealer.

○ If genuine oil is not available, use an anti-oxidant added quality

oil expressly labeled for air-cooled 2-cycle engine use (JASO

FC GRADE OIL or ISO EGC GRADE). Do not use BIA or TCW

(2-stroke water-cooling type) mixed oil.

○ Never use for four-stroke engine oil or waste oil.

○ Always mix fuel and oil in a separate clean container.

Always start by ﬁ ling half the amount of fuel, which is to be used.

Then add the whole amount of oil. Mix (shake) the fuel mixture. Add

the remaining amount of fuel.

Mix (shake) the fuel-mix thoroughly before ﬁ lling the fuel tank.

Fueling

WARNING

○ Always shut oﬀ the engine and let it cool for a few minutes

before refueling.

○ Slowly open the fuel tank, when ﬁ lling up with fuel, so that

possible over-pressure disappears.

○ Tighten the fuel cap carefully, after fueling.

○ Always move the unit at least 3 m from the fueling area before

starting.

○ Do not smoke and/or allow ﬂ ames or sparks near fuel when

handling or ﬁ lling fuel.

○ Always wash any spilled fuel from clothing immediately with

soap.

○ Be sure to check for any fuel leakage after refueling.

Before fueling, clean the tank cap area carefully, to ensure that

no dirt falls into the tank. Make sure that the fuel is well mixed by

shaking the container, before fueling.

Starting

CAUTION

Do not start if the pipe and guard net is obstructed.

1. Check the switch (7) to ON position. (Fig. 4)

* Push priming bulb (8) several times so that fuel ﬂ ows through

the bulb or return pipe (9). (Fig. 5)

2. Set choke lever to CLOSED position. (Fig. 6)

3. Pull recoil starter briskly, taking care to keep the handle in your

grasp and not allowing it to snap back. (Fig. 7)

4. When you hear the engine want to start, return choke lever to

RUN position (open). Then pull recoil starter briskly again.

WARNING

○ Never start or run the engine inside a closed room or building

and/or near the inﬂ ammable liquid. Breathing exhaust fumes

can kill.

○ Do not allow the rope to snap back in and always hold the unit

ﬁ rmly.

NOTE

If engine does not start, repeat procedures from 2 to 4.

5. After starting engine, allow the engine about 2–3 minutes to

warm up before subjecting it to any load.

* If the engine stops and is hard to restart straightaway, allow it

to cool before trying again.

Operating blower (Fig. 8)

○ A low speed should be used to blow leaves and dry grass.

○ A medium speed should be used to clean wet leaves and grass.

○ A high speed should be used when moving gravel, dirt or other

heavy materials.

WARNING

○ Do not direct discharge of air toward people or pet.

○ The unit should be operated in a well ventilated area.

○ Never perform assembly or disassembly procedures with

engine running or serious personal injury may result.

○ Never touch muﬄ er, spark plug, or other metallic parts while

engine is in running or immediately after shutting oﬀ engine.

SPECIFICATIONS

000Book_TRB24EAP_WE.indb 5000Book_TRB24EAP_WE.indb 5 2012/07/09 17:33:132012/07/09 17:33:13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tanaka TRB24EAP-TA Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info