Bedienungsanleitung Tascam CD-RW901SL (Seite 32 von 42) (Englisch)

587264

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

IMPORTANT SAFETY PRECAUTIONS

32 TASCAM CD-RW901SL

5 − Recording

32 TASCAM CD-RW901SL

Continuous recording (CONT REC)

Using two CD-RW901SL units to make continuous recording.

1 Connect two CD-RW901SL units using the

PARALLEL ports.

Unit 1 Unit 2

EOM TALLY (5 pins) FADER START/STOP

(11pins)

FADER START/STOP

(11 pins)

EOM TALLY (5 pins)

GND (8 pins) GND (8 pins)

2 On both units, select the CONT REC sub-menu in

the REC option (see “Operation basics” on page 16).

Cont Rec> XXX appears on the display where

XXX shows time setting of 30s, 60s or 90s to trigger

the units to start recording when the EOM (End of

Message) tally signal is received one after another.

NOTE

OFF is also shown in the time setting, however if

selected, the CONT REC function is canceled.

We recommend selecting the same time setting on

both units.

The CD-RW901SL may take longer for OPC calibra-

tion for discs with scratches, grime or dust. To avoid

clipping a recording, we recommend not to use such

discs, or to select a time setting more than 30s.

3 Connect recording source(s) to both units.

4 Press REC key on the one of the units to start

continuous recording, and Cont Rec lights up in

the display.

While the one unit is recording, the second unit

should be in stop mode.

When the remaining time on a disc being recorded

reaches the time setting, the unit sends the EOM

tally signal to the second unit.

Simultaneously, Now OPC is displayed on the

second unit, and when OPC calibration completes,

the unit starts recording.

The two units are now in recording mode during

the time setting selected.

When the first unit finishes recording, the recorded disc

should be replaced with another recordable disc for the

next recording which starts when the unit receives the

EOM tally signal from the second unit. This loop recording

will be continued until either of the units is stopped.

NOTE

While the ﬁrst unit is recording, the second unit can

be set in recording standby mode. However, it may

shorten the unit’s lifetime by running the motor

continuously. We recommend to set the second unit in

stop mode during stand by.

If the number of tracks is restricted, the EOM tally

signal is not output and the continuous recording

cannot be operated.

The CONT REC function remains selected even the

power is turned off, so that when the power is turned

on again on one of the units, and when the following

conditions are met, the unit starts recording:

Both units are connected

The unit has a recordable disc

To avoid recording accidently, remove the recordable

disc from the unit before turning off the power, or

disconnect the units from each other.

Use two CD-RW901SL units connected only when

CONT REC is operated. In any other operation, two

units should be disconnected, or set the CONT REC

function off on both units to avoid any unexpected

recording.

•

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam CD-RW901SL Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info