617901
12
Zoom out
Zoom in
Vorherige Seite
1/64
Nächste Seite
12
TASCAM DA-6400/DA-6400dp
2 – Names and Functions of Parts
Note about the PARALLEL connector
The PARALLEL connector on the back of the unit allows
external control of it.
You can set the functions of the PARALLEL connector on the
PARALLEL INPUT
and
PARALLEL OUTPUT
pages. (See
“PARALLEL connector settings” on page 38.)
The factory default pin assignments are as follows.
Pin No. I/O Function (default value)
1 O OUTPUT AUX1 (STOP TALLY)
2 O OUTPUT AUX2 (REC TALLY)
3 I INPUT AUX1 (TAKE SKIP +)
4 I INPUT AUX2 (TAKE SKIP −)
5 O OUTPUT AUX3 (ERROR TALLY)
6 I INPUT AUX3 (FADER REC)
7 I INPUT AUX4 (REW)
8 GND
9 O OUTPUT AUX4 (PLAY TALLY)
10 O OUTPUT AUX5 (PAUSE TALLY)
11 I INPUT AUX5 (F.FWD)
12 I STOP
13 I PLAY
14 I INPUT AUX6 (PAUSE)
15 +5V
I: For command input and transport control
Internal circuit with +5V pull-up
Operates with low signal input of 50 msec or longer
When INPUT AUX is set to FADER REC, low signal input
starts recording and high signal input stops recording.
When INPUT AUX is set to FADER START, low signal input
starts playback and high signal input pauses playback.
O: For command and tally output
Internal circuit is open collector (10Ω output impedance)
Outputs low command during operation
20V dielectric strength, 35mA maximum current
+5V: 50mA maximum supplied current
The following example is of a connection that controls recording
and playback of this unit by level, using fader starts and stops
and FADER REC commands.
START
STOPSTOP
Pin 8 : GND
Pin 6 : REC
NOTE
Setting multiple FADER REC and FADER START settings to
INPUT AUX is not possible.
Home Screen
The following information is shown on the unit's display.
1 Transport status
This icon shows the current transport status.
Icon Meaning
Playing back
In playback standby
Stopped
Searching backward
Searching forward
Searching backward (high speed)
Searching forward (high speed)
Recording
In record standby
2 Repeat status
When repeat playback is off, the icon is unlit.
When repeat playback is on, the icon is lit.
3 Solo status
When the solo selection frame is white, the icon blinks.
4 Take number
This shows the number of the take playing or being
recorded.
5 Time counter
This shows the elapsed recording/playback time of the take
or the timecode time.
6 Time display mode
This icon shows the current time display mode.
Time
display
mode
Meaning
This shows the elapsed time from the beginning
of the take.
This shows the remaining time until the end of
take. When recording, this shows the remaining
time until the maximum file size is reached.
This shows the total take elapsed time.
During playback, this shows the total take
remaining time. When recording, this shows the
remaining available recording time.
This shows the timecode time of the recording/
playback take.
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tascam DA-6400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info