Bedienungsanleitung Tascam DA-6400 (Seite 18 von 64) (Englisch)

617901

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

TASCAM DA-6400/DA-6400dp

3 – Preparation

NOTE

During installation, be careful not to tighten the screw too

much.

Connecting and disconnecting USB

flash drives

You can connect and disconnect USB flash drives whether the

unit is on or off.

CAUTION

Do not disconnect a USB flash drive when it is being

accessed in one of the following manners.

Doing so could damage data or the USB flash drive.

Moreover, disconnecting the USB flash drive during the

execution of a firmware update could result in the unit

becoming unable to start up or operate properly.

i During execution of the

FACTORY PRESET

function

i During execution of a

SYSTEM BACKUP

IMPORT or

EXPORT

i During execution of a firmware update

i When the

BROWSE

screen is open and the USB flash

drive is being accessed

Installing I/O cards (sold separately)

CAUTION

Before installing or removing an I/O card (sold separately),

disconnect the power cord from the outlet or the unit.

1. Remove the two screws from the plain panel and remove

the panel itself. (If a different card is already installed,

remove it.)

2. Insert the I/O card into the card slot. Align the edges of the

I/O card with the white guides inside the slot and insert it

securely. Push the I/O card in until its backplate reaches the

back panel of the unit, leaving no gap, and clicks into place.

Do not force the card into the slot. If you cannot insert the

card properly, remove it once and try reinserting it.

3. Use the two removed screws to secure the I/O card in place.

4. Turn the unit on, and check the

VERSION INFOR-

MATION

screen to confirm that it has recognized the

inserted I/O card. (See “Checking the firmware version” on

page 51.)

If “SLOT1 : ---- (None)” or something similar appears, the card

might not be inserted correctly or the screws might not be

tightened securely. Insert the I/O card securely into the unit

again.

Turning the unit on and off (putting it

in standby)

When the unit is off, press the STANDBY/ON switch on the front

of the unit to turn it on.

DA-6400dp startup screen

Home Screen

After the unit starts and the startup screen is shown, the Home

Screen will open.

If no SSD/HDD is loaded in the slot or there are no audio files in

the current folder, the take number and time will not be shown

on the Home Screen.

Turning the unit off:

Press and hold the STANDBY/ON switch to open a pop-up

message.

When the confirmation pop-up is open, press and hold the

MULTI JOG dial to turn the unit off.

CAUTION

•

Do not turn the unit off (put it into standby) during

recording, playback or at other times when data on the

SSD/HDD is being accessed. The SSD/HDD case indicator

blinks orange at such times. Doing so could cause proper

recording to fail, recorded data to be lost, and sudden loud

noises from monitoring equipment, which might damage

the equipment or harm hearing.

•

When the unit is started up for the first time (or when the

built-in clock is reset after being left unused without power

for a long time), the

CLOCK ADJUST

screen appears

after the start-up screen to allow the date and time of the

built-in clock to be set. (See “Setting the built-in clock date

and time” on page 19.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam DA-6400 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info