Bedienungsanleitung Tascam DP-008EX (Seite 43 von 92) (Englisch)

617893

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

TASCAM DP-008EX

6 – Basic Recording

Monitoring input signals

To monitor an input signal press the REC button for

the TRACK set to record that signal. This will light/

blink its REC indicator.

NOTE

When recording, the playback and input signals

are mixed and output from the PHONES and LINE

OUT jacks and can be heard through connected

headphones or a connected external monitoring

system (powered speakers or an amplifier with

speakers).

OL indicators and level meters

The audio levels of this unit can be checked using the

INPUT A/B OL indicators and the level meters on the

display.

The level meters allow the signal levels to be checked,

and they can also be used to confirm whether signals

are being input into the unit. For example, if the

and level meters are moving a signal is being input

into the unit even if you cannot hear anything when

you are monitoring with headphones or an external

monitoring system (powered monitor speakers or an

amplifier and speakers). In this case, something other

than this unit is probably the reason that sound is not

being output.

As shown below, if a “–” appears at the top of a level

meter, the input is overloading (these “–” indicators

will automatically disappear after a while). In this

case, the sound might be distorted, so lower the level

until the “–” stops appearing.

If an OL indicator lights, the input source signal could

be too loud or the LEVEL knob set too high.

If the OL indicator lights even if the LEVEL knob is set

to MIN, the input source signal is too high, so lower

the volume on the input source.

erload indicators

Input level meters (A/B)

The and level meters on the display show the

input levels of this unit’s INPUT A and INPUT B.

Use the INPUT A/B LEVEL knobs,

INPUT SETTING

screen settings and the output volume controls of the

input sound source to adjust the levels.

NOTE

If an INPUT A/B OL indicator lights even though

the INPUT A/B level meters shows a suitable level,

the input signal is too strong and the sound is

distorted. Lower the output volume of the input

sound source.

TRACK level meters (1–8)

These meters show either playback signal levels

or the track input signal levels, depending on the

operation status, as shown below.

REC indicator

Transport

status

Signals shown

by level

meters

Unlit Playing back Track playback

Blinking

(recording

standby)

Playing back Track playback

Blinking

(recording

standby)

Stopped Track input

Lit (recording) Recording Track input

NOTE

When the playback signal is shown, the level of the

recorded signal of the track is shown, so the level

shown by the meters cannot be changed. When

the input signal is being shown, the INPUT A/B

LEVEL knobs can change the levels shown by the

level meters.

Stereo level meters (L/R)

These show the stereo bus output level of this unit.

Adjust the output level with the MASTER LEVEL

knob.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam DP-008EX Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Tascam DP-008EX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info