Bedienungsanleitung Tascam DP-008EX (Seite 52 von 92) (Englisch)

617893

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

TASCAM DP-008EX

7 – Recorder Functions

Confirming the result

Raise the bounce destination TRACK LEVEL knob

(turn other TRACK LEVEL knobs all the way down)

and the MASTER LEVEL knob, and start playback

from the beginning of the song. If you are not

satisfied with the result because, for example, the

balance between instruments is poor, or the pan

settings are wrong, use the undo function. (See

“Undoing operations (undo)” on page 49.)

If you are satisfied with the result, when the

recorder is stopped press the BOUNCE/MIXDOWN/

MASTERING button to open the

RECORDER MODE

screen and select

MULTI TRACK

After bouncing tracks, you can record again on

(overwrite) tracks other than the bounce tracks.

TIP

If it is possible that you might need the original

tracks at some later time, back-up the track data to

a computer or copy the song before bouncing(See

“Copying songs” on page 40.) (See “Connecting

with a computer” on page 75.)

Locate and search functions

Direct locate function

The current recorder position is shown at the top of

the Home Screen in “hours: minutes: seconds: frames”

(30 frames per second).

You can move the current recorder position to a

specific time by inputting it here.

1. On the Home Screen, use the HOME button

to move the cursor (underline) between time

counter divisions.

You can edit the value at the cursor positions.

The seconds are selected in the following figure.

2. Use the DATA wheel to change the value above

the cursor(underlined).

When adjusting, the value will carry over

automatically when it reaches the highest or

lowest value in a field. For example, when using

the DATA wheel to increase the value in the

seconds field, the number will change from 59 to

0 and the minutes value will increase by one.

NOTE

When the DATA wheel is being turned, the

following pop-up message appears.

3. Press the HOME button to move to a different

time division and use the DATA wheel to change

the value.

4. After setting the desired time value, press the

Play (7) button to start playback from that

position.

Returning to the song beginning (RTZ

function) or the point where recording

was last started (LRP function)

Use simple button operations to return to the

beginning of a song (00h00m00s00f) or to locate to

the position where recording last started.

RTZ is short for “Return To Zero,” and LRP is short for

“Last Recording Position.”

Return To Zero (song beginning at 00h00m00s00f)

Press them [RTZ] button while pressing and

holding the Stop (8) button.

Last Recording Position (the position recording

last started)

Press the , [LRP] button while pressing and

holding the Stop (8) button.

This function is useful when you want to record the

same passage again.

Search backward/forward

When stopped, press the m [RTZ] button/, [LRP]

button to search backward/forward.

Each time you press one of these keys, the speed

increases from 10x to 50x, 100x and 1000x.

During playback, press and hold the m [RTZ]

button/, [LRP] button to search backward/

forward. During playback, the search backward/

forward speed is fixed at 10x.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam DP-008EX Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Tascam DP-008EX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info