Bedienungsanleitung Tascam DP-02CF (Seite 30 von 80) (Englisch)

617899

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

IMPORTANT SAFETY PRECAUTIONS

30 TASCAM DP-02/DP-02CF

2 – Advanced techniques

Meters to let you know what’s going on with the audio in

the unit. Here are a few little hints and tips which may help

you.

As well as showing you the level of signals, the meters

can show you if the signals are actually getting to the unit.

Even if you can’t hear anything and the input meters are

showing a signal, it means that the connections from the

instrument to the unit are okay (and you should probably

check your monitoring equipment levels).

It’s important to remember that meters should never be

continuously at the top of the bar. If they are, it means the

level is too high, and you will probably experience distor-

tion. Digital distortion is unpleasant (unlike, say, tube

guitar amp distortion), and you need to avoid it.

Input meters

These meters (A and B) show the level of the signal coming

into the unit. Adjust the level with the front panel controls,

or the instrument volume control, if available.

Track meters

These meters (1 through 8) show the volume of the signal

recorded on the track (un-armed tracks) or entering the

track (armed tracks). Remember that the faders do not

control the level of signals sent to the track, and will never

affect the track meter readings.

Master meters

These meters (L and R) show the master level at all times.

The MASTER fader controls the level of these meters.

Using the meters

These marks are used for setting the points at which auto-

mated punch recording starts and ends and for repeat

playback, as well as for track editing. You can set these

marks while playing back, recording, or while playback is

stopped.

Set IN and OUT marks by pressing and holding the SHIFT

key and pressing SET IN or SET OUT keys at the appropri-

ate points.

NOTE

IN and OUT marks are also used (along with the TO

mark, which is set and used in the same way) when

performing track editing functions.

Locate to the IN and OUT points by simply pressing IN

and OUT.

Fine-tune the position of the IN and OUT points by press-

ing and holding SHIFT and pressing POINT EDIT:

Edit the point, to 1/10 frame accuracy, using the cursor

keys and the DATA dial, in the same way as for direct loca-

tion (“Direct location” on page 29).

Press YES/ENTER when done.

IN and OUT marks

1. Press and hold both LOCATE LIST keys togather to

show the location mark list.

2. Use the DATA dial to select a mark and press the ¥

cursor key to bring up the LOCATE TRIM screen.

NOTE

The marks are shown in the order they appear in the

song, not by number.

3. Use the dial to move the mark backwards and

forwards by 1/10 frame (the right most digit of the

number). You can’t move a mark forward past the

next mark in the list, or backwards to before the

previous mark in the list.

T I P

1/10 frame is 1/300 of a second about 3.3 milliseconds

4. When done, press YES/ENTER or NO/EXIT to

return to the LOCATE TRIM screen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam DP-02CF Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Tascam DP-02CF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info