617895
71
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
TASCAM DP-24SD
71
14 – Troubleshooting
When working with this unit, if something is not going the way you want, or if you experience any difficulties, etc., first refer to this
troubleshooting section. It contains the most common troubles, the probable causes, and the corrective measures. Also, see “15 –
Messages” on page 72 for the meaning of messages that may pop up on the display. Consult this table when a message appears when
an operation cannot be completed by the unit.
The SD card is not recognized.
Confirm that the SD card is completely inserted.
Why can't I hear any sound when I play back?
Are the track faders of the tracks set to a proper level?
Is the STEREO fader set to a proper level?
Have you connected the PHONES or MONITOR OUT jack to
your monitoring system properly?
Is your monitoring system set up correctly?
Is the MONITOR LEVEL knob set to a proper level?
(PHONES jack only)
The sound I am trying to record sounds distorted.
Aren't the INPUT A to H TRIM knobs on the top panel of
the unit set too high?
Isn't the input source too loud?
Isn't the monitoring system distorted because the monitor
level is too high?
Why can't I record?
You must have at least one track in recording standby (REC
indicator flashing) before you start recording by pressing
the RECORD (0).
Are input sources assigned to tracks? (See Assigning inputs”
on page 35.)
Noise occurs if I connect a passive guitar or bass
directly.
Connecting another device to the unit's stereo output
(STEREO OUT) jacks might reduce the noise.
This might be caused by interference noise from another
device. If there is a power amplifier or other device that uses
a large transformer, a fluorescent light or something similar
nearby, you might be able to reduce the noise by changing
the distance and orientation of this unit in relation to such
equipment.
The unit turns off.
This product is compliant with the European ErP standby
power regulations. In order to comply with these
regulations, the automatic power saving function is set to
30 minutes when the unit is shipped from the factory. So, by
default, the unit will turn off automatically after 30 minutes
elapse without any operation. Change the automatic
power saving function setting if you want to disable it. (See
“Setting automatic power saving” on page 63.)
71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tascam DP-24SD wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info