Bedienungsanleitung Tascam DP-32 (Seite 40 von 104) (Englisch)

617894

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

40 TASCAM DP-32

6 - Basic Recording

5. After selecting all the tracks that you want to

change, press the F4 [t] button.

A “Erase selected tracks. Are you sure?” pop-up

message appears.

6. Press the F2 [YES] button to change all the tracks at

once.

CAUTION

When the track type is changed, the audio for that track

is cleared, so the track will have no audio signal. If you

make a mistake, however, you can undo this operation

to restore the track type and audio on it. (See "Undoing

an operation" on page 47.)

NOTE

•

When the track type is changed, the input assignment is

cleared, so you should make assignments now.

•

If you set track 9/10 as a mono track, it will become track

9, for example. Likewise, if 31/32 is set to mono, it will

become track 31. (The even numbered track is skipped.)

Assigning inputs to mono tracks

1. When the recorder is stopped, press the ASSIGN

button to open the Assign screen.

2. Use the SELECT button of each track or the CURSOR

(5/b/g/t) buttons to move the cursor to the

mono track to which you want to assign a recording

source.

3. Press the SOURCE button of the desired input (A to

H) or turn the JOG/DATA dial to set the input source

of each mono track.

4. After making the settings, press the ASSIGN button

or the HOME button to return to the Home screen.

Selecting the input sources

This unit is equipped with eight inputs (INPUTS A to H),

and each of them has a standard XLR/TRS combo jack.

In addition to microphones and line level instruments,

you can connect guitars to the INPUT H jack. When

connecting a guitar, set the LINE-GUITAR switch on the

rear panel to GUITAR.

TIP

When connecting an electric-acoustic guitar with a built-

in preamp or an active-type electric guitar, or when using

an effects pedal, for example, between the guitar and this

unit, set the LINE-GUITAR switch on the rear panel to

LINE.

Assigning inputs

When using this unit, "assigning inputs" means setting

the recording source for each track to INPUT A to H on

the Assign screen.

Assign screen

NOTE

•

By default, the recording sources of tracks

are

assigned to inputs A to H, in that order.

•

Assignments are saved when you save a song or turn the

unit off. Likewise, assignments are loaded when you load

a song.

This unit can simultaneously record a maximum of eight

tracks. You can assign one input source to multiple tracks

simultaneously, but you cannot assign multiple input

sources to the same track. You can also assign an input

source to a direct stereo bus.

Setting the track type

You can set tracks 9/10–31/32 to be used as either stereo

or mono tracks. By default, they are all stereo tracks.

Change these settings on the Assign screen.

1. When the recorder is stopped, press the ASSIGN

button to open the Assign screen.

2. Use the STEREO SELECT button of each track or the

CURSOR (5/b/g/t) buttons to move the cursor

to a track that you want to change.

3. Press the F3 [ST/MONO] button to change the type

of the selected track.

4. If you want to change the type of other tracks,

repeat steps 2 and 3.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam DP-32 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info