Bedienungsanleitung Tascam DP-32 (Seite 71 von 104) (Englisch)

617894

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

TASCAM DP-32 71

11 - Various Other Functions

MIDI remote control

The mixer, effects and recorder of this unit can be remotely

controlled by other devices using MIDI messages.

For more information about MIDI messages that can be

used to control this unit, see "18 - Appendix" on page 97.

When the transport is stopped, press the MENU button to

open the

screen, select (highlight blue) the

MIDI

item, and then press the F4 (t) button to open the

MIDI

screen.

MMC MODE

Set the MIDI Machine Control transmission/reception

mode.

OFF: MMC communication disable.

MASTER: This unit functions as the MMC master.

SLAVE: This unit functions as an MMC slave.

When the unit is the MMC master, the MMC command

is output by the MIDI OUT jack, and it is possible to

remotely control an external MIDI sequencer or another

DP-32 unit.

When the unit is the MMC slave, MMC commands can

be received through the MIDI IN jack, and it is possible

to remotely control this unit from an external MIDI

sequencer or another DP-32 unit.

MMC Device ID

Set the MMC device ID.

Select from

127

, and

ALL

. (Default:

ALL

)

Master units send MMC commands with device IDs that

slaves with the same IDs can receive. When ALL is selected,

however, MMC commands are sent and received for all IDs.

MMC is used for remote transport control of MIDI

equipment. On the other hand, MIDI Time Code (MTC) is

used for synchronization with MIDI equipment. Note that

the MMC mode and MMC device ID are not related to

mixer and effect remote control.

REMOTE CONTROL

Use MODE to set this unit as a master or a slave.

Use PROGRAM CHANGE EFF to set whether this unit's

effect changes when a program change message is

received (ON or OFF). In Mastering mode, program change

messages are not received even if this is ON.

Use CONTROL CHANGE to set whether or not received

control change messages control the parameters of this

unit's mixer and effects (ON or OFF).

Tuner function

You can use the built-in chromatic tuner to tune guitars.

1. Connect a guitar or bass to the MIC/LINE INPUT H.

Tuning cannot be performed with instruments

connected to MIC/LINE INPUTS A to G.

2. Set the LINE-GUITAR switch on the rear panel to

GUITAR. (See "Selecting the input sources" on page

40.)

3. When the recorder is stopped, press the MENU

button to open the

screen.

4. Use the JOG/DATA dial to select the

TUNER

item and then press the F4 (t) button.

The

TUNER

screen opens.

5. Use the JOG/DATA dial or the CURSOR (5/b)

buttons to set the standard frequency of A4.

The setting range is from

435Hz

445Hz

. (Default:

440Hz

)

6. Play the instrument and begin tuning.

The pitch name closest to the string appears above

the meter.

Tune the instrument so that the target pitch name

appears and the center of the tuning meter lights.

A bar appears to the left or right of the center if the

sound is lower or higher than the target pitch. The bar

becomes longer as the sound shifts away from the

target pitch.

When the pitch played matches the note shown, the

center , t and g icons light green.

7. After tuning the instrument, press the HOME

button to return to the Home screen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam DP-32 Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info