Bedienungsanleitung Tascam dr 1 (Seite 23 von 43) (Englisch)

152393

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

TASCAM DR-1 23

Overdubbing

Overdub recording

Preparation for overdubbing

8–Recording

By overdubbing, you can play an instrument or sing as

you play back a saved track and mix and record both

sounds in a new le.

Follow these procedures to prepare for overdubbing.

Set the ﬁle type to WAV

Only WAV les can be created by overdubbing.

1 Press the MENU key to open the Menu Screen.

2 Use the wheel to select

REC SETTING

(highlighted in inverse) and press the

¥/π key.

3 Use the wheel to select

FORMAT

and press

the

¥/π key.

4 Use the wheel to select

WAV 16-bit

WAV

24-bit

5 Press

STOP/HOME to return to the Home Screen.

NOTE

The playback track can be either an MP3 or a

WAV le.

Turn

MONITOR

ON in the Input Setting Screen

1 Press the SETTING key to open the Input

Setting Screen.

2 Use the wheel to select the

MONITOR

item and

press the

¥/π key.

3 Use the wheel to select

This status allows you to always monitor the input

signal. In other words, you can monitor a mix of

the track being played back and the input signal.

4 Press

STOP/HOME to return to the Home Screen.

TIP

By making the above settings, in addition to overdubbing,

you can use a recorded (or copied) audio track for vocal or

instrument practice, as well as karaoke.

Before beginning these procedures, in addition to

setting the le type to

WAV

and turning

MONITOR

ON, set the input and adjust the level if necessary.

1 When the Home Screen is displayed, use the

µ and ≤ keys to select the track for playback.

2 Press the

¥/π key to start playback, and check

the volume balance between the playback and the

input sounds.

3 Use the

MIX BALANCE keys as necessary to adjust

the balance by increasing or decreasing the

playback signal volume.

During adjustment using the keys, the playback

volume appears the lower part of the display.

4 Press REC/PAUSE to begin recording standby.

The screen overdubbing ON/OFF pop-up appears.

The recording file name, input source, recording

audio file type and sampling frequency also

appear so that you can confirm them before you

start recording.

5 Use the wheel to select

from the overdubbing

ON/OFF pop-up.

6 Press the

REC/PAUSE key to start overdubbing.

When recording starts, the REC/PAUSE key lights

and the display shows the elapsed and remaining

recording times.

The lower part of the screen shows the name of

the playing file that is being mixed in the overdub.

7 To stop recording, press the

STOP key or directly

select a track for playback on the Browse Screen

(See “Browse Screen” on page 27).

CAUTION

You cannot pause when overdubbing (the REC/PAUSE key

is inoperative).

NOTE

Set the ﬁle type to WAV for overdubbing (see “Selecting •

ﬁle type and sampling frequency” on page 19). If you try

to overdub when the ﬁle type is set to MP3 “

Format

is MP3

” appears and operation is prevented.

To play a track that is not in the currently selected •

playback area, you can select the track directly on the

Browse Screen (See “Browse Screen” on page 27), or

you can change the selected playback area on the Play

Mode Screen before conducting the above operation.

(See “Setting the playback area” on page 24.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam dr 1 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info