Bedienungsanleitung Tascam DR100 MKII (Seite 20 von 60) (Englisch)

490765

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

TASCAM DR-100MKII

3 – Preparation for Use

Preparing the power

Power source options

This recorder can be powered by the included TASCAM BP-

L2 lithium-ion rechargeable battery, two AA batteries, a

TASCAM PS-P520 AC adaptor (sold separately) or a TASCAM

BP-6AA external battery pack (sold separately). By using

both the lithium-ion rechargeable battery and AA batteries

together, the unit can be operated continuously for a long

time. Moreover, when, for example, the charge becomes

low in one type of battery, batteries can be changed while

the unit continues to operate. Alkaline and nickel-metal

hydride AA batteries can be used with this recorder.

NOTE

Manganese dry cell batteries (R6) cannot be used with

•

this unit.

This unit cannot recharge Ni-MH batteries. Use a

•

commercially available recharger.

Using the lithium ion battery

Open the battery compartment cover on the side of the

unit, insert the battery with the correct orientation into the

compartment, and then close the cover again.

Charging the lithium ion battery

There are two ways to charge the lithium ion battery.

Charging with an AC adaptor

Connect a TASCAM PS-P520 AC adaptor (sold separately) to

the unit's DC IN 5V connector. Charging takes about three

hours. (See “Using an AC adaptor (sold separately)” on page

21.)

Charging with a computer

Connect with a computer using the included USB cable.

Charging takes about six hours. (See “7 – Connecting with a

Computer” on page 47.)

NOTE

Connect this unit to the computer directly. Proper

•

operation cannot be guaranteed when using a USB hub.

When connected by USB, recharging occurs even if the

•

unit’s power is off.

When recharging through the USB port, the unit will

•

switch to USB connection mode, so other functions

cannot be used.

The

•

CHARGE indicator lights while charging and turns

off when charging is complete.

CHARGE

indicator

Using AA batteries

Open the battery compartment cover on the back of

the unit, install the two batteries with the correct +/–

orientation and close the battery compartment cover.

When using AA batteries, set the type of battery in order

to accurately show the amount of power remaining and

allow the unit to accurately determine whether power is

available for proper operation. (See “Setting the type of AA

batteries (AA BATTERY)” on page 51.)

Using both types of batteries together

If you install both the lithium ion battery and AA batteries,

you can set one as the main power source and the other as

the backup. (See “Setting the main battery source (MAIN)”

on page 50.) By doing this, when the amount of power

left in the main source becomes insucient for operation,

the unit automatically switches to the backup source,

allowing continued operation. Moreover, you can change

the backup while operating using the main power source.

This allows you to continue to use the unit for long periods

of time. (See “Changing batteries when the power is on” on

page 50.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam DR100 MKII Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Tascam DR100 MKII

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info