490765
24
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
24
TASCAM DR-100MKII
3 – Preparation for Use
3 Press the . or / button to move the cursor
(highlighted area), and use the wheel to change
values.
4 Press the ENTER/MARK button to confirm the change
and return to the
MENU
screen.
NOTE
While setting the time, the time display stops changing.
You can set the unit to automatically add the date to file
names. (See “Setting the format of file names” on page
51.)
CAUTION
The date and time setting can only be maintained for a
few minutes if the unit is not powered from batteries or
through the TASCAM PS-P520 AC adaptor (sold separately).
When using batteries, replace them before they completely
lose power.
Inserting and removing SD cards
Inserting the card
NOTE
An SD card is already installed when the unit is shipped
from the factory. If you want to use this card to record and
play tracks, there is no need to reinstall it.
1 Open the SD slot cover on the rear panel.
2 Insert the SD Card into the slot as shown in the
following illustration until it clicks into place.
Removing the card
1 Open the SD slot cover.
2 Press the SD card in gently and then release it to
allow it to come out.
CAUTION
Do not remove the SD card from the unit when it is
connected to a computer by USB.
NOTE
SD cards that meet SD or SDHC standards can be used
with this unit.
A list of SD cards that have been confirmed to work with
this unit can be found on our website (http://tascam.
com/).
SD card write protection
SD cards have protect switches that prevent writing new
data to them.
Unprotected Protected
If you slide the protect switch to the “LOCK position, le
recording and editing is not possible. Move the switch
to the unlocked position in order to record, erase and
otherwise edit data on the card.
Preparing an SD card for use
In order to use an SD card in this unit, you must format it
rst.
CAUTION
Please use a PS-P520 AC adaptor (sold separately) or
make certain that there is sufficient remaining battery
power when formatting a card.
Formatting a card erases all the data on it.
1 Confirm that an SD card is installed and turn the
power ON.
2 The following message appears when a new card
or a card formatted for use with another device is
installed in the unit.
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tascam DR100 MKII wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Tascam DR100 MKII

Tascam DR100 MKII Bedienungsanleitung - Deutsch - 68 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info