Bedienungsanleitung Tascam HS-2 (Seite 90 von 132) (Englisch)

617907

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

90 TASCAM HS-2

•

If the space on either of the media storage devices runs

out or an error occurs during recording with

Mirror

set, recording to the media storage device with no

space remaining or to the media storage device on

which an error has occurred will stop. Recording of the

current file to the other media storage device will stop.

However, recording to the next take as a new file will

start.

Then, the message and media storage device remaining

space display button will be shown as follows:

1 If either of the media storage devices has run out of

space

Media storage device remaining space button

2 If a recording error has occurred on either of the

media storage devices

Media storage device remaining space button

FILE FORMAT page

Make settings related to the file format.

Bit Length

Set the quantization bit rate for recording files using the

following buttons.

Setting buttons:

16bit

(default),

24bit

Max File Size

Set the maximum size for recording files using the

following buttons.

Setting buttons:

640MB

1GB

2GB

(default)

Pause Mode

Set whether or not to divide files when a recording is

paused using the following buttons.

Setting buttons:

SPLIT

(default),

NO SPLIT

OPTIONS page

Make settings related to the pre-recording and auto

markers.

PreREC Time

Turn this function ON or OFF and set the length of

pre-recording time. (Default:

OFF

)

When

PreREC Time

, the signal input during

recording standby is captured by the built-in memory for

the set amount of time, allowing a maximum of 5 seconds

to be recorded before recording is started manually.

To set the pre–recording time, touch the knob, and adjust

the value using the DATA dial.

Setting range:

–

seconds (default:

seconds)

Auto Marker

Make settings related to auto markers.

Audio Over:

Use this to add markers when the set audio level is

exceeded.

Turn this function ON or OFF and set the detection

level. (Default:

OFF

)

To set the detection level, touch the knob, and

adjust the value using the DATA dial.

Setting options:

–0.20dB

(default),

–0.17dB

–0.13dB

–0.10dB

–0.06dB

–0.03dB

Settings made here are reflected in the

Over

Level

setting on the

METER SETUP

screen.

Time Interval:

Use this to add marks at fixed time intervals. Turn

this function ON or OFF and set the time interval.

(Default:

OFF

)

To set the time, touch the knob, and adjust the

value using the DATA dial. The range of setting

values is 1–10 minutes (default:

minutes).

Sync Unlock:

Use this to add a mark when synchronization with

the master clock is lost. Turn this function ON or

OFF. (Default:

OFF

)

PRE / REC / END:

Marks are attached automatically on the PREREC

start point/ recording start point/ recording end

point. Set the ON / OFF status of the functions.

(Default:

OFF

)

10–Internal settings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam HS-2 Seite 90

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info