617907
95
Zoom out
Zoom in
Vorherige Seite
1/132
Nächste Seite
TASCAM HS-2 95
Frame Type
Set the time code frame type of the currently loaded
project.
Setting buttons:
23.976F
,
24F
,
25F
,
29.97DF
(default),
29.97ND
,
30DF
,
30ND
I/O page
Set the synchronization signal status display and time
code output on this page.
NOTE
If the Option SY-2 has not been installed, the display is
shaded and the setting cannot be selected.
STATUS
This shows the status of synchronization signals.
TIMECODE IN:
When time code is input, the time code frame rate is
shown.
WORD/VIDEO IN:
When a synchronization signal is detected at this
connector,
WORD
,
VIDEO
or
TriLevel
is shown.
TC Out Mode
Use the buttons to set the time code output mode.
GenOut button:
Time code is output from the internal time code
generator.
PlayOut button (default):
In timeline mode, the time code time for playback and
recording is output. In take and playlist modes during
playback, the time code recorded in the file is output.
Remote settings (REMOTE SETUP)
Make settings for the PARALLEL, RS-232C, RS-422 and
Ethernet (Network) connectors.
The
REMOTE SETUP
screen has 5 pages:
GENERAL
,
PARALLEL
,
RS-232C
,
RS-422
and
ETHERNET
. Touch
the tabs at the bottom of the screen to open the corre-
sponding page.
GENERAL page
Make the external remote controller settings on this page.
FADER MODE
Allows the fader on an external TASCAM RC-HS20PD
remote controller (sold separately) to be enabled or
disabled. When set to
Disable
, the internal fader is fixed
at 0 dB.
Setting buttons:
Disable
,
Enable
(default)
FADER Start MODE
When the fader start function of an external TASCAM
RC-HS20PD remote controller (sold separately), for
example, is on, set whether fader starts, which allows
you to start playback by raising the fader from when in
playback standby, is enabled or not.
Setting buttons:
Disable
,
Enable
(Default)
FADER Stop MODE
When the fader start function of an external TASCAM
RC-HS20PD remote controller (sold separately), for
example, is on, set whether fader stop, which allows you
to put playback into standby by lowering the fader to
during playback standby, is enabled or not.
Setting buttons:
Disable
,
Enable
(Default)
NOTE
If both the
FADER Start MODE
and
FADER Stop MODE
items are set to
Disable
, the fader start function of the
external TASCAM RC-HS20PD remote controller (sold
separately) will be turned off automatically, and the
FADER START indicator will turn off. In this state, if you
touch the Fader Start key on the TASCAM RC-HS20PD
remote controller, a
Cannot Change Now. Fixed in
current mode
warning appears in a pop-up window.
10–Internal settings
95

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tascam HS-2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info