617905
13
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
TASCAM HS-8 13
PARALLEL connector
The PARALLEL connector on the rear panel allows external
control of this unit. The pin assignments are as follows.
Pin No. Function In/Out
1 GND
2 PLAY/Flash 1 In
3 STOP/Flash 2 In
4 RECORD/Flash 3 In
5 SKIP FWD/Flash 4 In
6 SKIP BWD/Flash 5 In
7 FLASH LOAD (STOP) In
8 FADER START In
9 FLASH Tally Out
10 READY Tally Out
11 RECORD Tally Out
12 STOP Tally Out
13 PLAY Tally Out
14 REMOTE Select In
15 PAUSE/Flash 6 In
16 CALL/Flash 7 InIn
17 AUX1/Flash 8 In
18 AUX2/Flash 9 In
19 AUX3/Flash 10 In
20 Flash Page In
21 Reserved
22 CF1 Tally Out
23 ONLINE Tally Out
24 CF2 Tally Out
25 +5V*
In: Command input, for transport control
Internal circuit, +5V pull-up
Operates with low commands of 50 msec or more
Out: Command output, for tally output
The internal circuit is open collector (output
impedance 10Ω)
Low command output when operating
20 V dielectric strength, 35 mA maximum current
*
+5V: 50 mA maximum supplied current
NOTE
The FLASH LOAD (STOP) (pin 7) functions are FLASH LOAD when
stopped and STOP during playback and when paused.
When Remote Select (Pin 14) is high, the input pins that have
two commands separated by a “/” (pins 2–6 and 15–19) in the
above table will perform the rst-listed function, and can be
used as conventional parallel controllers.
When this pin is low, the above-listed input pins will function as
ash start keys. Moreover, the key assignments will be as follows
according to the high/low state of pin 20.
#14 #20 Flash-start take
Low High 1–10
Low Low 11–20
The following example is of a connection that uses a fader to
start and stop playback of this device.
For information about the assignment of AUX1-3 (pins
17-19) functions, see the “PARALLEL tab” of the REMOTE
SETUP screen on page 48.
RS-232C Connector
The RS-232C connector on the rear panel can be
connected to an RS-232C connector on a computer to
allow control of this unit from that computer.
Makes settings related to communication on the REMOTE
SETUP screen RS-232C page. (See “RS-232C page on page
48.)
NOTE
Please contact TASCAM customer support for information about
this unit’s RS-232C command protocol.
RS-422 connector
You can control this unit remotely by connecting the
RS-422 connector on its rear panel to a controller or editor
compatible with SONY P2 protocol (RS-422).
Make settings related to operation on the REMOTE SETUP
screen RS-422 page. (See “RS-422 page” on page 48.)
NOTE
Please contact TASCAM customer support for information about
this unit’s protocol compatibility.
2 − Names and functions of parts
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tascam HS-8 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info