Bedienungsanleitung Tascam HS-8 (Seite 46 von 72) (Englisch)

617905

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

46 TASCAM HS-8

MASTER

Select the master clock to use.

INT (default value): Use this unit’s internal clock.

WORD: Synchronize with the word clock input through

the WORD/VIDEO IN connector.

VIDEO: Synchronize with the video clock input through

the WORD/VIDEO IN connector.

CH1-2DIN - CH7-8DIN: Synchronize with the clock of the

digital signal (AES1-8, AES A-B, or ADAT1-8) selected as

the digital input for CH1-2, 3-4, 5-6, or 7-8.

You cannot select an input as the master clock if the

sampling rate converter is ON for that input.

The second line of the button shows the name of the

selected digital input signal.

NOTE

A check mark appears on the button of the currently active

•

master clock.

If synchronization from an external clock is interrupted, the

•

unit’s internal clock becomes active. In this case, a check mark

appears on the INT button to show that it has become the

active clock, and an “x” appears on the button of the selected

external clock that was lost.

SYNC page

Make setting related to synchronization.

STATUS

Shows the status of the currently loaded project’s

sampling frequency and clock synchronization.

Play Fs

When playing a take with a sampling frequency of 48 kHz,

48 kHz pull-up, or 48 kHz pull-down, the unit can be made

to synchronize with an external clock by setting it to play

back with pull-up or pull-down.

Depending on the combination of Project sampling

frequency and Play sampling frequency settings, the unit

will operate with the Fs shown below.

Play sampling frequency setting

Project

sampling

frequency

OFF (Default

setting)

Pull-down Pull-up

48 kHz 48 kHz 48 kHz – 0.1% 48 kHz + 0.1%

48 kHz pull-up 48 kHz + 0.1% 48 kHz Not possible

48 kHz pull-

down

48 kHz – 0.1% Not possible 48 kHz

All others Project

sampling

frequency

Not possible Not possible

NOTE

Set this to OFF before recording. Recording is not possible when set

to Pull-up +0.1% or Pull-down –0.1%. If you try to record when not

OFF, “Cannot REC” appears in a warning pop-up window.

TC Chase

Use to turn playback synchronized with external timecode

ON/OFF (default value: OFF). Set it to ON, when you want

to match the timing of this unit’s audio with a timecode

master unit (audio recorder or video).

You can also set timecode offset (TC Offset) with the

timecode master device. Touch the “EDIT” button to open

the “TC Offset” screen where you can set the offset value

in a range between “−23: 59: 59.29” and “+23: 59: 59.29”

(default value: “00: 00: 00.00”).

NOTE

TC Chase can also be turned ON/OFF by pressing the SHIFT and

CALL keys at the same time.

TC Rechase

Turn this function, which re-synchronizes when

synchronization with external timecode becomes

inaccurate, ON/OFF (default value: “OFF”). To set the

amount of inaccuracy that triggers rechase, touch the

knob and turn the DATA dial to select a value in frames of

1/3, 1, 2, 5 or 10 (default value: 2 frames).

T/C page

Make settings related to time code.

Free run mode

6 – Internal Settings and Operations

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam HS-8 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info