Bedienungsanleitung Tasco 119203C Digital Trail Camera (Seite 3 von 12) (Englisch)

569827

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

QUICK GUIDE: TASCO TRAIL CAMERA

1. Open the camera by releasing the latches on the right side of the camera. Install 4 “D” cell batteries (at base of all batteries

contacting springs), and insert an SD card (not included, use any capacity up to 2GB) in the slot to the right of the 5 buttons

(upside down, brand name facing you). Press the card down until you hear it click into place.

2. Press and release the Power switch. If you are using the camera for the rst time, you should set the date and time so your

photos will be “stamped” correctly. Briey press the Menu button-the “year” digits will blink on the display. Use the Up/Down

buttons to set the current year, then press Enter, and repeat to set the month and press Enter again. The display will then

change to let you set the date. After setting the date, press enter, and set the time (the “hour” digits will ash, use Up/Down to

set the hour and then minute. The time display uses the 24 hr standard, so 2:00 PM is indicated as “1400”, etc).

3. After the date and time have been set, and Enter is pressed, you have a choice of three operating modes: Still photos with

“Lo” resolution (this is the default setting if you don’t change it), Still photos with “Hi” resolution, or movie (video) mode. To

change modes, press Up or Down to cycle through the choices (each will blink), pressing Enter to set the mode you prefer.

4. In normal operating mode, the display will only show the still photo or movie clip icon in the lower left corner, an SD card

icon on the lower right, and one or more digits that indicate how many photo or movie les have been stored on the card. To

test the camera operation, wave your hand in front of the lens and PIR (passive infrared/motion) detector, while looking at

the LCD display. As long as events are being detected, a new still photo or movie clip (as set in previous step) will be recorded

every 30 seconds, indicated on the display by “SnAP”, then “SLP”. Note: for movie clips, the display will stay on “SnAP” for the 15

sec duration of each movie.

5. Thread the strap through the slots on the back of the Trail Cam and attach the buckles, then strap it onto a suitable tree,

making sure the strap is tight and the camera is aimed at the area you wish to observe. Turn on the camera (make sure a new

or empty SD card has been inserted) and leave the area-there is a 60 second delay after power on before the rst photo is

taken. Alkaline batteries typically last 30 days or more, depending on how often the Trail Cam is activated, how often the ash

res, ambient temperature, etc.

6. To look at your captured photos, make sure the power is o, and remove the SD card by pushing down lightly on the top

edge of the card-it will pop up for removal. Use an SD card reader with any PC or Mac to view, copy, or delete the photos

(standard JPG les) and movies (AVI les) inside the “DCIM/100MEDIA” folder on the card. Double click on an individual le

to see it, or open the les with the photo software of your choice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tasco 119203C Digital Trail Camera Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info