Bedienungsanleitung TC Helicon Ditto Mic Looper (Seite 11 von 15) (Englisch)

658242

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Creating loops

Ditto Mic Looper English Manual – 2014-11-17 9

Creating loops

Recording your first loop

Important: On the following pages, operation

is described based on the default operation

mode of Ditto Mic Looper (Record loop > Play-

back > Record overdubs). You can also use an

alternative operation mode. See “Setting opera-

tion mode”.

To start recording, press the LOOP footswitch

once. The LED will light up in red, indicating Ditto

Mic Looper is in Record mode.

At the end of the loop (for example, after eight

bars), press the LOOP footswitch again.

The LED will turn green, and Ditto Mic Looper

will repeat the loop continuously. The LED will

blink every time Ditto Mic Looper reaches the

starting point of the loop.

Your loop can be up to five minutes long.

Setting loop playback volume

To change the playback volume of the loop you

just recorded, adjust the LOOP LEVEL knob.

The LOOP LEVEL knob only controls loop play-

back level – it has no influence on the signal from

your microphone.

Overdubbing

When you’re happy with your original loop, you

can start overdubbing.

To record another take (overdub), press the

LOOP footswitch again while the original loop is

playing back. The LOOP footswitch LED will turn

red, indicating you’re in Record mode again.

When you’re done, press the LOOP footswitch

once more to quit Record mode.

Ditto Mic Looper will repeat the loop with both

the original recording and the overdub.

Please note that the length of the loop will

never increase when overdubbing. When you

continue recording, you will simply create addi-

tional overdubs. You can record as many over-

dubs as you like – there is no limit.

Undo (clearing the last take)

To undo the last take you recorded (i.e., remove

it), simply press and hold the LOOP footswitch

for 1.5 seconds or longer. You can undo the last

take both during playback and when playback is

stopped.

The LED will blink twice in rapid succession, and

the last take will be cleared (removed). Previously

recorded takes will stay intact.

Redo (restoring a previously

cleared take)

If you have cleared (removed) the last take us-

ing Undo and you have changed your mind, you

can restore that take. To do so, simply press and

hold the LOOP footswitch for 1.5 seconds or lon-

ger during playback.

The LED will blink twice in rapid succession, and

the previously deleted take will be restored.

Using Undo/Redo creatively

Undoing and redoing overdubs can be used

for more than just correcting mistakes. You can

make your performance more interesting by re-

moving and bringing back sections. Here is a

simple example:

► Sing a bass line (loop cycle 1).

► Use a Harmony pedal (for example TC-Heli-

con Harmony Singer) to create harmonies and

record these (loop cycle 2).

► Record a melody (loop cycle 3).

► Press and hold the LOOP footswitch to clear

the last take, i.e., remove the melody. Impro-

vise or record something else.

► Press and hold the LOOP footswitch again to

bring back the previously cleared melody.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

TC Helicon Ditto Mic Looper Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TC Helicon Ditto Mic Looper

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info