Bedienungsanleitung TC Helicon VoiceLive Rack (Seite 40 von 89) (Englisch)

658357

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

The Setup Button

The I/O Tab

f IN GAIN

Sets and displays the MIC / LINE input level.

Both inputs share the same gain settings and are

not meant to be used simultaneously; switching

from a Mic to a Line level signal will likely require

resetting IN GAIN. To set input level automatically,

use the AUTO MIC-GAIN function by holding

the Input Gain button and following the prompts.

When any digital input is selected (USB or SPDIF)

the IN GAIN does not control the digital input

level. Use your transmitting device to adjust level.

f PHANTOM

Turns 48V phantom power on and off for use

with condenser microphones.

f AUX LEVEL

Set the input level of for the Aux input.

f OUTPUT

The congures the outputs to be STEREO (de-

fault), MONO or DUAL MONO. The STEREO

option outputs discrete Left and Right audio

material when connected to a stereo monitor or

PA system.

In MONO mode, the Left output is the summed

mono mix of VoiceLive Rack including effects. The

Right output is dry with only Tone applied to the

MIC or LINE input signal. This is useful when a live

sound engineer wants to control the balance of

wet/dry mix at the mix position. In this case, set

LEAD MUTE to ON.

In DUAL MONO mode, the effected vocal

comes from the left output and effected guitar is

produced from the right output. This allows you

to have a sound tech control the level balance

between wet vocal (vocal with harmonies and

effects) and wet guitar.

f DIGITAL IN

Selects between SPDIF and USB physical inputs

as the input and also species where the incom-

ing digital signal is routed. By default the routing

is USB: STEREO, where the digital input is routed

to the same path as the AUX input, but is not

passed on to the digital output.

When set to USB: VOX L / INST R, or S/PDIF:

VOX L / INST R the digital input replaces the

analog MIC/LINE and GUITAR inputs and the

MIC and GUITAR IN connections are disabled.

Sample rate is synchronized automatically to the

incoming digital audio stream. There is no sample

rate adjustment in VoiceLive Rack. When process-

ing an analog input such as the MIC and sending

to VoiceLive Rack’s digital out, sending a short bit

of audio from your recording application to either

Digital input will set the sample rate.

When DIGITAL IN is set to USB (or SPDIF):

STEREO, harmonies will follow the stereo audio

coming from the selected digital input on presets

where NATURALPLAY is set to AUX INPUT.

While the VoiceLive Rack is connected via USB

to your computer, other applications such as your

browser may not make sound through your regu-

lar sound card. In this case, disconnect VoiceLive

Rack’s USB cable.

f DIGITAL OUT

Congures the digital output between the stereo

mix of VoiceLive Rack (FULL MIX), and separated,

dry outputs used for recording (VOCAL & GUI-

TAR).

f LEAD MUTE

Turns the lead voice off in all presets. This is useful

in the live sound engineer setting described above

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

TC Helicon VoiceLive Rack Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TC Helicon VoiceLive Rack

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info