Bedienungsanleitung Teac CD-RW890 (Seite 18 von 28) (Englisch)

487962

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Recording (2)

S-LVL-60/50/40/30 (The track numbers are automatically

added)

The auto track function activates and “A-TRACK” appears. The

displayed number indicates the increment level.

The track numbers are automatically added during recording. If a

track change is detected via DIGITAL or if silence (lower than the

increment level) continues for three seconds or longer then the

next track starts (when sound becomes louder than the increment

level) via ANALOG, and the track numbers are automatically

updated.

* Increment level

Sound level to detect “silence” to add track numbers using auto

track when recording from external devices via ANALOG or to

perform synchronous recording for digital sources such as CD, MD,

and DAT.

This instruction manual describes “silence” as the situation where

the recording source level is lower than the specified increment

level.

−60, −50, −40, and −30 dB can be selected.

MANUAL (The track numbers are not automatically added)

In MANUAL mode, the track numbers are not automatically added.

To add track numbers manually, press the RECORD button.

The setting can be configured for DIGITAL and ANALOG respectively. <

When the power is turned on, the setting is –60dB for DIGITAL, and

–50dB for ANALOG.

The setting is stored until the power is turned off. <

If a CD is recorded via DIGITAL, the track numbers are added based <

on the CD's digital signals. There is usually no need to change the

increment level.

In digital recording, even if the auto track function is activated, <

track numbers may not be added depending on the digital source

player.

When you record digital broadcasts or other sources without <

track numbers, track numbers are not added even if the auto track

function is activated. To add a track number, press the RECORD

button while recording a track.

When you record classical music or other sources containing silent <

parts via ANALOG, track numbers may not be properly added even

if the auto track function is activated. To add a track number in this

case, deactivate the auto track function, and press the RECORD

button while recording a track.

When you record a record or other sources with much interference, <

more track numbers than expected may be added unintentionally.

The AUTO/MANUAL button cannot be used during recording. <

If track numbers are not properly added

When you record sources with interference via ANALOG, track

numbers may not be added if the increment level is lower than the

interference level. In this case, set the increment level higher than

the interference level.

If there is little interference and the track starts with a small sound

resulting in the beginning of the recorded track being truncated,

set the increment level lower.

Press the RECORD button.

and J indicators on the display will light, and the unit

enters the record pause mode.

No button will work while “WAITING” is displayed. Wait a few <

seconds until “WAITING” disappears from the display. When DIGITAL

is selected in step

, the sampling frequency of the digital source

( “ F S 4 4 _ 1K ” , “FS 48K” or “ FS 32K”) briefly appears after

“WAITING”.

“DIN UNLOCK” appears when the unit cannot perceive the digital <

signal. In that case, connect a digital device to the DIGITAL IN

terminal, switch it on, and wait a few seconds until the unit enters

the record pause mode.

You cannot record if “MONITOR” appears on the display. In that <

case, reload a recordable disc, wait a few seconds until “NO TOC”

and “CD-R” (or “CD-RW”) indicators light on the display, then press

the RECORD button again.

If necessary, adjust the recording level using the REC LEVEL

buttons.

The recording level can be adjusted only when “ANALOG” is

selected in step

The recording level is 0 dB when the power is turned on. Usually,

recording is possible even if the recording level has not been

adjusted.

CD-RW890_E_vA_unlocked.pdf 18 10/09/08 17:17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teac CD-RW890 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Teac CD-RW890

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info