Bedienungsanleitung Teac TU-1000 (Seite 9 von 44) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

487963

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Basic Operation (1)

Power ON / OFF

Connect the power cord and signal cable of the unit.

Then, press the POWER button on the front panel to turn the unit on

(R). The power indicator on the front panel is on and the unit is in

normal operating mode now.

To turn the unit off, press the POWER button on the front panel.

The button is set to the off position (E), and the power indicator and

eventually the unit are off. Disconnect the AC power cord from the

main outlet when the appliance is not used for a long period of time.

Band selection

Pressing the BAND button on the front panel or the remote control

will toggle through FM/AM/AUTO.

When you select FM mode, “M” (MHz) is lit in the display and “F”

appears after the station code.

Example:

For 01F 104.30M,

“01” is the station code, “F” is for FM, and “104.30M” is the station

frequency.

When you select AM mode, “K” (KHz) is lit and “A” appears in the

display after the station code.

Example:

For 01A 1404K,

“01” is the station code, “A” is for AM, and “1404K” is the station

frequency.

When you select FM AUTO mode, “AT”, “F”, “M” and the station code

are all shown in the display.

Example:

For 01F 104.30M,

“ST” is stereo reception, “AT” is FM AUTO mode, “F” is for FM, and

“104.30M” is the station frequency.

FM/AM reception band

Auto selection:

Press the Band button for “FM” or “AM”.

Press and hold down the TUNING j button (m) to tune in a lower

frequency. When a station is found, the tuning process will stop

automatically. The display shows “ ”.

Press the TUNING k button (,) to tune in a higher frequency.

When a station is found, the tuning process will stop automatically.

The display shows “ ”.

Manual selection:

Press the MODE button and the station frequency will blink in the

display. Turn the TUNING knob on the front panel or hold down either

TUNING j or k button (m or ,) and release it when the

station you want to listen to is found. The frequency changes in fixed

steps; “FM” is 50KHz, and “AM” is 9KHz.

Direct input selection:

Input the frequency of the broadcast you want to hear with the

number buttons.

Example:

When you know a station frequency, you can directly input that

frequency to select that station. When you know that the FM

station frequency is 104.30MHz, press the FREQ button on the

remote control and “------M” appears in the display. Then, press

numbers 1, 0, 4, 3, and 0 in sequence.

When the first number is bigger than 1, the display begins o

with the second number. When the first number is 1, the

second number shows as "0".

In FM mode, the last number you pressed is bigger than or o

equal to 5 shows as "5", and the number less than 5 shows as

"0".

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teac TU-1000 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Teac TU-1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info