Bedienungsanleitung Team HC 13 (Seite 12 von 34) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

487000

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

Generated by Unregistered Batch DOC TO PDF Converter

2011.3.804.1511, please register!

Copies of the I/B. Please reproduce them without any changes

except under special instruction from Team International

BELGIUM. The page must reproduced and folded in order to

obtain a mini booklet B5 (+/- 150 mm width x 210 mm height).

The page must be folded in order to keep the good numbering

when you turn the page of the I/B . Don’t change the page

numbering. Keep the languages integrity.

Assembly page 12/34

Fax +32 2 359 95 50



CUTTING HAIR WITH THE ATTACHMENT COMBS (see Page 3: )

 Only cut a small amount of hair to start with until you become accustomed to the length each

attachment comb gives to the hair.

 We suggest you try the longest attachment comb B on the clipper first.

 For uniform cutting, never push or force the clipper through the hair at a fast pace. The clipper

works most efficiently when it works at its own speed.

 Start by combing the hair in its natural direction.

 Attach the attachment comb B to your clipper and start by trimming the sides from the bottom

upwards. Hold the clipper lightly against the hair with the comb teeth pointing up but flat against

the head. Slowly lift the clipper up and outward through the hair, cutting only a small amount at

a time  and .

 If you want shorter hair, either change to the comb A or change the hair length (see  - ). You

can also apply more pressure to the present attachment comb. This procedure requires practice,

and it is always better to leave too much hair during the first few haircuts .

 For the top of the head, you will give a fairly short cut if you use the attachment comb A. With

the teeth flat against the head, slowly start trimming from the front to the back. Again, it is better

to leave the hair longer at the beginning .

Outlining

 Outlining requires no attachments.

 Comb hair into the required style. Position clipper between the sideburns and the ear. Make sure

the outer edge of the blade is against the hairline. With the outline of the hair as your guide,

slowly move the clipper around the ears . For the back of the neck and the sideburns, hold the

clipper upside down , and move downwards holding it against the skin at the length desired.

Short cuts

 Always cut from the back of the neck to the crown, using the attachment comb B. Holding it flat

against the head, slowly move the clipper up through the hair. Use the same technique for the

sides, cutting from the bottom to the upper side of the head .

 For the front of the crown, cut the hair against the direction in which it grows. Then even it up

with the sides .

 To taper hair down to the neckline, use attachment comb A. Comb hair, check for uneven spots

and outline sideburns and neckline .

MAINTENANCE

 Your clipper was carefully examined before leaving our factory to ensure that the blades were

oiled and aligned. To maintain your clipper in peak condition, the blades should be oiled every

few haircuts.

 Use the small brush to remove remaining hair.

 Change the blades as soon as they become blunt.

DISPOSAL OF BATTERIES

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Team HC 13 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info