Bedienungsanleitung Team HC 14 RCE (Seite 11 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

487001

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced

and folded in order to obtain a booklet A5 (+/- 148.5 mm

width x 210 mm height). When folding, make sure you

keep the good numbering when you turn the pages of

the I/B. Don’t change the page numbering. Keep the

language integrity.

Assembly page 11/40

Fax +32 2 359 95 50

MOUNTING (see Page 2: B)

 To mount the comb attachment, put the locking knob in  position (see page 3, E, 25)

and insert the comb as described on page 2, B. The "clicks" that you can hear correspond

to the different cutting length settings. Once the comb stops, it means that it is in

position"1".

 To remove the comb attachment, proceed the other way around, still making sure that

the locking knob is in  position.

 Once you have chosen the cutting length, put the locking knob in  position to block the

comb.

To attach the comb, hold it with teeth up and snap comb attachment firmly to the appliance.

The comb attachment can be set to 7 cutting length positions:

1. 1/6"

2. 1/4"

3. 1/3"

4. 5/12"

5. 1/2"

6. 7/12"

7. 2/3"

CUTTING HAIR WITH THE COMB ATTACHMENT (SEE PAGE 2: C and PAGE 3)

 Only cut a small amount of hair to start with until you become accustomed to the length

the comb attachment gives to the hair.

 We suggest you try the longest comb attachment in position “7” on the clipper first.

 For uniform cutting, never push or force the clipper through the hair at a fast pace. The

clipper works most efficiently when it works at its own speed.

 Start by combing the hair in its natural direction.

 Place the comb attachment in position “7” to your clipper and start by trimming the sides

from the bottom upwards. Hold the clipper lightly against the hair with the teeth of the

comb attachment pointing up but flat against the head. Slowly lift the clipper up and

outward through the hair, cutting only a small amount at a time (8 and 9).

 If you want shorter hair, either place the comb attachment in position “1” or change the

hair length (see B, 6). You can also apply more pressure to the present comb attachment.

This procedure requires practice, and it is always better to leave too much hair during the

first few haircuts (10).

 For the top of the head, you will give a fairly short cut if you place the comb attachment in

position “1”. With the teeth flat against the head, slowly start trimming from the front to the

back. Again, it is better to leave the hair longer at the beginning (11).

Short cuts

 Always cut from the back of the neck to the crown, placing the comb attachment in

position “7”. Holding it flat against the head, slowly move the clipper up through the hair.

Use the same technique for the sides, cutting from the bottom to the upper side of the

head (14).

 For the front of the crown, cut the hair against the direction in which it grows. Then even it

up with the sides (15).

 To taper hair down to the neckline, use attachment comb in position “1”. Comb hair,

check for uneven spots and outline sideburns and neckline (16).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Team HC 14 RCE Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info