Bedienungsanleitung Team hc 18 (Seite 9 von 36) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

401579

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced and

folded in order to obtain a booklet A5 (+/- 148.5 mm width x

210 mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t change

the page numbering. Keep the language integrity.

9 TEAM HC 18 - 070626

Assembly page 9/36

Fax +32 2 359 95 50

cover facing the head), the top of the blades perpendicular to the skin and cut to the

desired length (7). If necessary, insist on the reluctant hair.

 When you get used to your hair clipper, you will be able to make layers simply by

changing the length of the combs in function of the cutting zone. These handling asks for

a special dexterity in order to obtain a correct result.

SHORT CUTS

 Always cut from the back of the neck to the crown, using the longest attachment comb.

Holding it flat against the head, slowly move the clipper up through the hair. Use the same

technique for the sides.

 For the front of the crown, cut the hair against the direction in which it grows. Then even it

up with the sides.

 For a flat top, use a flat comb, not the attachment comb. Just cut hair on top of the head

over it. To taper hair down to the neckline, use closer cutting attachment combs. Comb

hair, check for uneven spots and outline sideburns and neckline.

 The four basic areas illustrated are your "road map" to easy do-it-yourself hair cutting (8).

LEVER

This lever has two main functions:

 Regulation of the cutting length because in the position short hair (lever pushed to the

front side) you can cut the length of the used combs or make outlining by pulling it to the

backside, you can make the cutting length longer (this allows middle cutting lengths

above the 4 delivered combs).

 Partial cleaning of the blades when in use by to and for motions in order to remove the

hair blocked in the blades.

MAINTENANCE

 Your clipper was carefully examined before leaving our factory to ensure that the blades

were oiled and aligned.

 Blades must be realigned if they have been removed for cleaning or replacement.

Therefore, as the lever is pushed to the front side in short hair position, the end of the top

blade teeth is

 Approximately 1.2 mm away from bottom blade. Compare your clipper blades with the

sketch (9).

 If the blade alignment is incorrect, add a few drops of oil to the blades, turn clipper on for

a few moments, turn off and unplug. Loosen screws slightly and turn the upper blade until

a correct alignment. Then tighten screws once the blades are aligned (10).

 Change the blades as soon as they become blunt.

 To clean the blades, use the small brush delivered with your appliance and if necessary,

remove them completely.

OIL

To maintain your clipper in peak condition, the blades should be oiled every few haircuts (12).

Do not use hair oil, grease or oil mixed with kerosene or any solvent, as the solvent will

evaporate and leave the thick oil which may slow down the blades' motion.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Team hc 18 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info