Bedienungsanleitung Team HC 19 R (Seite 13 von 51) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

487004

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced

and folded in order to obtain a booklet A5 (+/- 148.5 mm

width x 210 mm height). When folding, make sure you

keep the good numbering when you turn the pages of

the I/B. Don’t change the page numbering. Keep the

language integrity.

TEAM HC 19 R - 110518

Assembly page 13/51

Fax +32 2 359 95 50

• For the front of the crown, cut the hair against the direction in which it grows. Then even it

up with the sides (15).

• To taper hair down to the neckline, use attachment comb in position “1”. Comb hair,

check for uneven spots and outline sideburns and neckline (16).

CUTTING WITHOUT THE COMB ATTACHMENT

Remove the comb attachment if you want to cut hair to a length of 1mm. To cut the hair with

the help of a comb or your fingers as well as to cut the outlines, you do not need the comb

attachment.

• Push the sliding lock switch to the unlock position.

• Take off the comb attachment by pulling it holding it by the sides (see page 2, B 6 and 7).

Cutting hair with the help of a comb or your fingers

Remove the comb attachment carefully, as explained in the previous paragraph.

Raise a wisp of hair with the help of the comb (17), or take the wisp between your fingers (18).

Take the wisp through the comb or fingers until only the desired hair length remains under the

comb/fingers. Cut the hair that is above the comb or fingers with the hair clipper (19 and 20).

Cutting hair with the integrated thinning function

The thinning function allows you to thin out your hair at some places to change the volume of

the hair cut.

• Push the switch upwards to the “THINNING” position.

• Take the wisp through the comb or fingers until only the desired hair length remains under

the comb/fingers and cut the hair that is above the comb or fingers with the hair clipper.

Outlining

• Outlining requires no attachments.

• Comb hair into the required style. Position clipper between the sideburns and the ear. Make

sure the outer edge of the blade is against the hairline. With the outline of the hair as your

guide, slowly move the clipper around the ears (12). For the back of the neck and the

sideburns, hold the clipper upside down (13), and move downwards holding it against the

skin at the length desired.

CUTTING A BEARD

• Lead the appliance against the grain of the beard.

• Comb the beard hair with the supplied comb so that it stands as high as possible, all in the

same direction.

• Put the comb attachment on the appliance and slide it to the desired cutting setting.

• Switch on the appliance (“CUT” position) and cut the beard.

Cutting the outlines of the beard

• Remove the comb attachment from the appliance.

• Hold the appliance in diagonal position with the front side pointing away from you.

• Start with the chin and cut backwards.

• Follow the chin line and cut the longer hair at the outside of the beard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Team HC 19 R Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info