Bedienungsanleitung Team HC 9 (Seite 12 von 35) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

486998

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

Generated by Unregistered Batch DOC TO PDF Converter

2011.3.804.1511, please register!

Copies of the I/B. Please reproduce them without any changes

except under special instruction from Team International

BELGIUM. The page must reproduced and folded in order to

obtain a mini booklet B5 (+/- 150 mm width x 210 mm height).

The page must be folded in order to keep the good numbering

when you turn the page of the I/B . Don’t change the page

numbering. Keep the languages integrity.

Assembly page 12/35

Fax +32 2 359 95 50



OUTLINING

 Outlining requires no attachments. Take the clipper and push the lever up to the close-cut

position.

 Comb hair into the required style. Position clipper between the sideburns and the ear. Make sure

the outer edge of the blade is against the hairline. With the outline of the hair as your guide,

slowly move the clipper around the ears (6). For the back of the neck and the sideburns, hold the

clipper upside down (7), and move downwards holding it against the skin at the length desired.

SHORT CUTS

 Always cut from the back of the neck to the crown, using the longest attachment comb. Holding

it flat against the head, slowly move the clipper up through the hair. Use the same technique for

the sides, cutting from the bottom to the upper side of the head (8).

 For the front of the crown, cut the hair against the direction in which it grows. Then even it up

with the sides (9).

 For a flat top, use a flat comb, not the attachment comb. Just cut hair on top of the head over it.

To taper hair down to the neckline, use closer cutting attachment combs. Comb hair, check for

uneven spots and outline sideburns and neckline (10).

 The four basic areas illustrated are your "road map" to easy do-it-yourself hair cutting (11).

MAINTENANCE

 Your clipper was carefully examined before leaving our factory to ensure that the blades were

oiled and aligned.

 Blades must be realigned if they have been removed for cleaning or replacement. To realign the

blades, simply match the upper and bottom blades teeth up, point for point. The end of the top

blade teeth should be approximately 1.2 mm away from bottom blade. Compare your clipper

blades with the sketch (12).

 If the blade alignment is incorrect, add a few drops of oil to the blades, turn clipper on for a few

moments, turn off and unplug. Loosen screws slightly and adjust. Tighten screws once the blades

are aligned (13).

 Change the blades as soon as they become blunt.

ADJUSTABLE LEVER

 The lever will extend the lifespan of your blades since a different cutting edge is used in each

setting. In addition, if extremely heavy hair cutting has jammed the blades, it will help you

remove hair that has become wedged between the two blades without removing them. While the

clipper is running, rapidly move the lever from "close cut" to "longer cut" a couple of times (14).

 The lever is conveniently located near your thumb. When the lever is in the uppermost position,

the blades will give you the closest cut and leave the hair very short. Pushing the lever

downward gradually increases the cutting length.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Team HC 9 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info