Bedienungsanleitung Team KA DV 2 (Seite 7 von 28) (Englisch, Französisch, Portugiesisch, Spanisch)

487050

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced and

folded in order to obtain a booklet A5 (+/- 148.5 mm width x

210 mm height). When folding, make sure you keep the

good numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language integrity.

7 TEAM KA DV 2 - 091219

Assembly page 7/28

Fax +32 2 359 95 50

INSTALLATION

1. Take the mounting plate out of the upper canopy (unscrew the 2 left screws and unscrew the

2 right screws lightly). Then attach the mounting plate firmly to the ceiling (Fig. 1).

2. Make the upper canopy slide onto the rod and insert the electric wires in the rod (Fig. 2).

3. Check if the metallic demi-ball is fixed correctly to the end of the rod (Fig. 3). If necessary,

screw back the screw.

4. Put the rod onto the motor hanger. Then insert the perforated nail (Fig. 4) in the

corresponding holes.

5. Put the split pin in the hole situated at the end of the nail (Fig. 5).

6. Attach the rod to the motor by tightening the supplied screws (Fig. 6).

7. Attach the obtained motor block to the mounting plate and make sure that the guide of the

mounting plate enters into the slot of the metallic demi-ball (Fig. 7).

8. Connect the wires of the light to the connector foreseen to this end.

9. Attach the upper canopy to the mounting plate (Fig. 9).

10. Tighten the upper canopy to the mounting plate (tighten the 2 right screws and add the 2 left

screws) (Fig. 10).

11. Assemble the fan blades and the blade holders (the nice side of the blade holders has to be

on the same side as the nice side of the fan blades). Use the supplied screws and washers

(Fig. 11).

12. Attach the fan blades to the motor block. To do so, remove the screws and washers of the

motor block, put one of the 1/4 pieces of carton with 2 holes between the blades and the

motor block, then fix the blades with the washers and screws (Fig. 12).

13. Connect the 2 wires of the lamp holder to the 2 wires of the motor block (respect the colours).

Then attach the lamp holder to the motor block (remove the 3 screws and 3 washers, place

the lamp holder, then fix it with the 3 screws and 3 washers) (Fig. 13).

14. Fix the tulip-shaped glass lampshades on the lamp sockets (3 screws per lampshade), then

insert the light bulbs (max. 60W) (Fig. 14).

15. Connect the chain to the switch of the appliance.

INSTALLATION OF THE WALL SWITCH

1. Switch box

2. ACTIVE

3. NEUTRAL

1. Check to make sure there is no electric current in your

electric power supply.

2. Attach the switch box to the wall.

3. Connect the wires of your electric installation to the box as

indicated on the pictures.

L : Light

F : Fan motor

USE

Switch on your appliance and check the good functioning of your appliance.

The chain/wall switch controls the fan as follows:

A. Pulling once/ Position HI --> High speed

B. Pulling twice/ Position MED --> Medium speed

C. Pulling three times/ Position LOW --> Low speed

D. Pulling four times/ Position OFF --> Stop

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Team KA DV 2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info