Bedienungsanleitung Team KA VT 15 (Seite 9 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

487057

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced

and folded in order to obtain a booklet A5 (+/- 148.5 mm

width x 210 mm height). When folding, make sure you

keep the good numbering when you turn the pages of

the I/B. Don’t change the page numbering. Keep the

language integrity.

9 TEAM KA VT 15 - 071011

Assembly page 9/32

Fax +32 2 359 95 50

ASSEMBLY

1. Loosen the fixing nut (16) from the lower pipe (14).

2. Insert the lower pipe (14) in the middle of the base (15) and tighten the fixing nut (16)

underneath the base (15) to fix the pipe to the base.

3. Slightly loosen the pipe fixing screw (13) and pull out the upper pipe (12) to the desired

length. Then tighten the pipe fixing screw (13).

4. Remove the fixing screw (11) located on the upper pipe and fit the motor housing (10)

with speed regulator into the upper pipe (12). Make sure the motor housing (10) is pushed

fully onto the upper pipe and that the hole of the upper pipe is in front of the hole located

on the motor housing. Attach the two parts with the fixing screw (11).

5. Loosen the guard mounting ring (6) from the motor housing (10).

6. Position the rear guard (7) firmly against the motor housing (9) and fasten by turning the

guard mounting ring (6) clockwise tightly.

7. Push the blade (5) along the motor shaft (8). Fasten it firmly with the cap (4) by turning it

counter clockwise.

8. Fit the front guard (2) and the rear guard (7) together with the position fixer (3) provided at

the front guard rim, and then clamp them together with the clips provided.

9. To ensure that it is impossible to have access to the fan blade without using a tool, a screw

is provided with this appliance in order to attach both parts of the mesh guard together.

This screw must be tightened on the lower part of the guards. We cannot be held

responsible for any injuries in case this screw had not been tightened before using the

appliance.

10. To change the height, loosen the pipe fixing screw(13) and slide the upper pipe to a

suitable height. Then tighten the pipe fixing screw (13) again.

OPERATION

 This appliance is equipped with 3 ventilation speeds. To switch on the appliance, turn the

rotary speed regulator into the desired position. To switch it off, put it in “0” position.

Speed settings:

0 = OFF

1 = Low

2 = Medium

3 = High

 This appliance also has an oscillation function:

 Push the oscillation knob (9) to switch on the oscillation.

 Pull the oscillation knob (9) to stop.

 It is also possible to tilt the upper part of the appliance in order to adjust the airflow

direction vertically.

CLEANING AND CARE

 Always disconnect the power supply cable from the power supply before carrying out any

cleaning operation.

 To remove dirt from the plastic surfaces, use a soft damp cloth. Use a vacuum cleaner to

remove the dust from the guards without having to disassemble them.

 Never immerse the fan in water or any other liquid.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Team KA VT 15 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info