Bedienungsanleitung Team TeCom-IP3 (Seite 14 von 27) (Deutsch, Englisch, Italienisch, Spanisch)

749145

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

EnglishEnglish

26 27

PTT-ID (BOT/EOT/Both)

The TeCom-IP3 can transmit a DTMF code via PTT-ID. Transmission of the code is

triggered by the PTT key. Each operation of the PTT key transmits the code.

BOT : The signal is transmitted upon pressing the PTT key.

EOT : The signal is transmitted upon releasing the PTT key.

Both : The signal is transmitted upon pressing and releasing the PTT key.

Priority Channel (Priv CH)

The priority channel can be selected out of the available channels. This is of impor-

tance for the function priority scan.

DTMF Code (ANI)

The DTMF code can contain a maximum of 8 digits, composed of the digits 0-9.

VOX (On/Off)

The voice activated transmission of the the signal, i.e. transmission without the PTT

key, is activated by the setting ON. The radio automatically switches to transmission

mode once the signal has a certain strength.

VOX Sensitivity (VOX Level)

The VOX sensitivity defines the threshold of the signal strength that is required to

start the automatic transmission.

On level 1, the signal must be very strong to trigger the VOX function. At level 9 the

VOX function reacts the most sensitive.

VOX Delay (Delay)

In VOX mode, after the signal ends, the radio remains in transmission mode for a

certain time before it switches back to reception mode. This avoids constant swit-

ching back and forth between transmission and reception mode when a pause du-

ring talking gets a little bit longer. You can set the delay time to the following

values: 0.3 / 0.5 / 1 / 1.5 / 2 / 6 seconds.

Tail Eliminate

Under certain circumstances, a clicking sound will be audible when the radio swit-

ches between transmission and reception mode. To diminish this occurence, the

tail eliminate function is useful. These options are available: 120° phase shift / 180°

phase shift / 240° phase shift / Freq eliminate tail.

Beep Tone (On/Off)

A beep tone informs you about a change of status, e.g. turning the radio on, low

battery, selection of an empty channel, activation or deactivation of a function by

pressing the PF1 / PF2 key, expiration of TOT.

Time-Out-Timer (TOT)

Excessive transmission without interruptions will increase the power consumption

and the temperature of the radio drastically. The Time-Out-Timer will restrict the trans-

mission time (between 30-300s in 30-seconds-steps). After expiration of the selected

time period, the radio automatically aborts transmission. After release of the PTT key,

it is possible to transmit again.

Battery Saving Function (Power Save)

The TeCom-IP3 is equipped with a battery saving function to reduce power con-

sumption in standby mode. After a certain time without any operation and no recep-

tion of a signal, the radio switches to standby mode, that provides the radio with as

little as possible current to not turn off. Once a signal is received or a operation per-

formed, the radio switches back to normal operation mode.

You can select between the ratio of normal mode and standby mode (1:1 - 1:10),

with 1:10 allowing a maximum of power saving.

Roger Tone (Roger Tone)

The roger tone, which is transmitted when releasing the PTT, confirms the end of

the message for all other stations on the same channel with a short signal.

Voice Annunciation (Voice)

The english voice annunciation announces the actual channel number and the on-

state when turning the radio on.

DTMF

The TeCom-IP3 can transmit a DTMF code via PTT-ID. Transmission of the code is trig-

gered by the PTT key. Each push and/or release of the PTT key transmits the code.

The following settings for the DTMF function are possible:

> tone length of the first digit (First Digit Time) - 50-4500ms in 50ms-steps

> time between the digits (Digit Inter Time) - 25-6400ms in 25ms-steps

> delay between pressing the PTT key and transmission of the DTMF code

(Digit Delay Time) - 25-6400ms in 25ms-steps

> DTMF signal audible at the transmitting radio (DTMF Side Tone)

CONNECTION

The TeCom-IP3 is equipped with a Motorola-compatible con-

nector (3.5 / 2.5 mm - stereo / stereo) that is used for ear-

/headphones and the data transfer cable for the software

T-UP31.

For further accessories please check the actual TEAM

catalogue or web site.

tecom-ip3_man_V5_18-2-14_Layout 1 14.02.2018 10:37 Seite 26

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Team TeCom-IP3 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info