5) Norm Selection
The version TS-6M Full Multi Norm can be set by the user to the following norms:
DE 80 FM
(26.565 - 27.405 MHz), 4 W / 40 AM (26.965 - 27.405 MHz), 1 W
EU 40 FM (26.965 - 27.405 MHz), 4 W / 40 AM (26.965 - 27.405 MHz), 1 W
EC 40 FM (26.965 - 27.405 MHz), 4 W
UK 40 FM (27.60125 - 27.99125 MHz), 4 W / 40 FM (26.965 - 27.405 MHz), 4 W
PL 40 FM (26.960 - 27.400 MHz), 4 W / 40 AM (26.960 - 27.400 MHz), 4 W
EI 40 FM (26.965 - 27.405 MHz), 4 W / 40 AM (26.965 - 27.405 MHz), 4 W
For changing the current norm, please hold the mode key ( 7 ) [ Mode ] while turning the
radio on. In the display, the symbol of the current norm appears, while all other symbols
disappear. Select the norm with the rotary channel selector ( 8 ) and confirm your selection
by turning the radio off and on again.
To confirm your selection, turn the radio off and on again or wait for approx. six seconds until
the radio automatically returns to operation mode.
Regarding the permissions and restrictions of the individual norms in the various european
countries, please check the radio passport, which is included in the scope of delivery. The
user is solely responsible for the selection of the permissible norm in the country of operation.
Note:
The norm TS-6M c (EC CEPT) is internally set to 40 channels FM / 4 Watts only.
The norm TS-6M i (EU CEPT) is internally set to 40 channels FM / 4 Watts, switchable
to 40 channels AM / 1 Watt. This version can be used in Switzerland.
6) Transmitting
To transmit, press and hold the key ( 4 ) [ PTT ] at the microphone ( 1 ). The TX symbol in the
LCD (6D) will appear and the s-meter (6A) shows the relative transmit signal strength.
For best quality, speak normally at a distance of 2 - 4 inches. Speaking too loudly will cause
distortions and make the signal difficult to understand.
While the set is in the transmit mode there is no key entry possible and the receiver is muted.
On completion of the transmission release the PTT key ( 4 ) and the radio will revert to receiv-
ing mode.
7) Call tone
If you press the call key ( 5 ) [ BP ] while holding the transmit key ( 4 ) [ PTT ], a calling tone
will be transmitted and can be heard by other participants, provided their radio is set to the
same channel and the same modulation type.
8) Priority Channel 9 / 19 [ CH9/19 ]
The TS-6M contains the priority channels 9 and 19. Priority channel 9 is selected by pressing
the key ( 14 ) [ CH9/19 ] once. To set priority channel 19, press the key ( 13 ) [ CH9/19 ] twice.
EnglishEnglish
9) Receipt-Signal Sensitivity [ RFG ]
Signals sent from immediate proximity can be too strong. It is advantageous to damp very strong
signals because they may be received very distorted and will not be clearly understandable.
With the RFG control [ RFG ] ( 11 ), the received signal strength will be diminished by reduc-
ing the receivers sensitivity.
No signal damping occurs when the control is turned clockwise all the way to the stop. This
should be the default setting for regular operation. Further turning counter-clockwise will de-
crease the receivers sensitivity.
10) Signal meter
The 6-step s-meter in the LCD (6A) indicates the signal strength of a received or send signal.
11) External speaker jack
The TS-6M is equipped with a 3.5 mm jack socket ( 16 ) at the rear panel to connect an exter-
nal speaker of 4 - 8 ohm impedance, e.g. TEAM TS-500. At 4 ohms the speaker load can be
4 watts. When the external speaker is connected, the internal speaker will be switched off.
Additional information
1) Safety instruction
Drivers must obey traffic rules regarding the use of transceivers in a vehicle.
The unit radiates RF energy in transmit mode. Please keep an eye on safety distance to the
antenna.
2) General precautions
Protect the mobile radio from humidity and dust. Do not store at places where the tempera-
ture may rise and cause damage, for example in the sun. The set can be cleaned by wiping
with a soft cloth. Do not use chemical products to clean the unit.
3) Servicing
The device must not be opened. Independent repairs or adjustment must not be carried out,
since each modification or unauthorized intervention will result in withdrawal of the operation
permit and of warranty and repair claims. Do not use the mobile radio if it seems not to func-
tion correctly. Disconnect the radio from the DC power source immediately. If there is a
defect, the authorized TEAM specialist dealer or TEAM must be contacted immediately.
4) Conformity
The CB mobile transceiver TEAM TS-6M complies to the European directive R&TTE and
meets the European standards EN 300 135-1/-2, EN 300 433-2, EN 301 489-1/-13 and EN
60950-1.
The specific regulations of the different versions in the different european countries can be found
in the radio passport that is included in this manual.
Specifications are subject to change without any prior notice or obligation on the part of the manufacturer.
16 17
