Bedienungsanleitung Team VT 18 (Seite 8 von 28) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

487597

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced

and folded in order to obtain a booklet A5 (+/- 148.5 mm

width x 210 mm height). When folding, make sure you

keep the good numbering when you turn the pages of

the I/B. Don’t change the page numbering. Keep the

language integrity.

8 TEAM VT 18 - 061125

Assembly page 8/28

Fax +32 2 359 95 50

ASSEMBLY

A. Base

The upper and lower part of the base must be fitted together before using the fan.

Insert the upper part (8) into the lower part (9) of the base, then press the upper part of the

base onto the lower part of the base till it clicks. Fix the two parts together with the 3 screws

provided. Do not over-tighten these screws.

B. Guards

1. Loosen the cap (2) from the motor housing by rotating it clockwise.

2. Loosen the guard mounting ring (5) from the motor housing by rotating it anti-clockwise.

3. Position the rear guard (6) firmly against the motor housing and fasten by turning the

guard mounting ring (5) clockwise tightly.

4. Remove and discard the PVC sleeve on the motor shaft.

5. Place the blade (3) along the motor shaft, locating the slot at the back of the blade on

the drive pin that passes through the motor shaft.

6. Fasten it firmly with the cap (2) by turning anti-clockwise.

7. Fit the front guard (1) and the rear guard (6) together with the clips provided. Attach the

front guard (1) to the rear guard (5) with the position fixer located on the front guard rim,

and then fit them together with the clips provided.

8. To ensure that it is impossible to have access to the fan blade without using a tool, a screw

is provided with this appliance in order to attach both parts of the mesh guard together.

This screw must be tightened on the lower part of the guards. We cannot be held

responsible for any injuries in case this screw had not been tightened before using the

appliance.

OPERATION

 This appliance is equipped with 3 ventilation speeds. To switch on the appliance, press

one of the speed knobs. To switch it off, press “0”.

Speeds:

0 = OFF

1 = Low

2 = Medium

3 = High

 This appliance also has an oscillation function:

 Push the oscillation knob (7) to switch on the oscillation.

 Pull the oscillation knob (7) to stop.

CLEANING AND CARE

 Always disconnect the power supply cable from the power supply before carrying out any

cleaning operation.

 To remove dirt from the plastic surfaces, use a cloth moistened with a little water. Use a

vacuum cleaner to remove the dust from the guards without having to disassemble them.

 Never immerse the fan in water or any other liquid.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Team VT 18 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info