Bedienungsanleitung Technics SA-DA10 (Seite 51 von 52) (Englisch)

536236

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

RQT5518

Unit doesn’t come on.

Sound is not heard.

Sound suddenly stops or

none is heard when the

unit is switched on.

“OVERLOAD” appears on

the display.

The AC mains lead plug is not fully inserted.

The speaker indicators are off.

The muting function is on.

Incomplete or incorrect connection to

speakers and external equipment.

The incorrect input source has been

selected.

The protection circuitry has functioned

because: the positive and negative speaker

wires have shorted; speakers with a lower

impedance than this unit’s rated impedance

are being used; the speakers are under

strain through excessive volume, excessive

power, or by being used in a high

temperature environment.

¡Confirm the plug is fully inserted.

¡Turn on the speaker indicators.

¡Press the muting button on the remote

control.

¡Check all connections.

¡Select the correct source.

¡Switch off the unit, determine and correct

the cause, then switch the unit on.

¡Use speakers with the right impedance

rating.

Common Problems

The tape monitor function is on. ¡Press the tape monitor button.

“F70” appears on the

display.

¡Turn off the unit and then turn it on again,

or disconnect the AC mains lead and then

connect it to your household mains socket

again.

(If “F70” remains on the display, consult an

authorized service center or your dealer.)

Problem Probable cause(s) Suggested remedy Page(s)

–

10–16

–

14–16

–

Cannot play CD, DVD, or

TV.

The DIGITAL input mode is set to DIGITAL

or ANALOG.

22¡Change the setting to suit the type of

connection you have made.

Digital signals this unit cannot decode are

being played.

¡Either have the player convert the signals

so this unit can handle them or switch to

ANALOG input.

22, 23

Nothing appears on the

display.

VGCA is ON. 27¡Nothing appears on the display while

VGCA is on. To turn the display on, press

and hold [VGCA].

The display is dim. The dimmer is on. 37¡Press [DIMMER] to restore the display to

normal.

The picture doesn’t appear

on the television.

Connection is incorrect. 10, 11¡Check and correct connections.

The television’s input mode is incorrect. –¡Change the input mode to suit the

connections between this unit and the

television.

Reference

If the surfaces are dirty

To clean this unit, wipe with a soft, dry cloth.

If the surfaces are extremely dirty, use a soft cloth dipped in a

soap-and-water solution or a weak detergent solution.

¡Never use alcohol, paint thinner or benzine to clean this unit.

¡Before using chemically treated cloth, read the instructions that

came with the cloth carefully.

MaintenanceThe RESET function

While the unit is on

While pressing and holding [DIGITAL

INPUT], press and hold [ /l] until

“RESET” appears on the display.

The operation settings for the unit will be initialized to the settings

made at the time of shipment.

However, any preset radio stations will not be erased.

DIGITAL INPUT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Technics SA-DA10 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Technics SA-DA10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info