Bedienungsanleitung Technics SC-CH515 (Seite 31 von 60) (Englisch)

637111

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

To stop recording:

_] Press 13.

To cut an unnecessary part while recording:

1. Press REC PAUSE.

The cassette deck will go into the recording standby state.

2. To resume recording, press <3 or D corresponding to the direc-

tion in which recording is taking place.

CCRT recording function:

CCRT (Computer Control Record Tuning) is the function which iden-

tifies the quality of the tape (concerning bias, level, equalizer) auto-

matically and sets the most desirable recording condition. While the

CCRT setting is activated, the CCRT indicator flashes. After the

setting has completed, CCRT indicator stops flashing.

The CCRT setting will remain in the system's memory even after the

power is switched to the standby mode.

The display shows the CCRT setting conditions as follows:

1. Bias setting

TIT L_IL.

III I1_1

I I

Recording level setting

il ;- FI

Recording equalizer setting

'--

iF--Ul

CCRT setting has been completed: "SET OK"

:f--Ill

oYou can make recordings in constant tone quality with use of the

CC RT function regardless of the different characteristics.

oWhen making an edit-recording from a CD, the CCRT function will

be automatically activated.

• Do not press INT or EXT while the CCRT is setting.

eDo not insert or remove the cassette tape after the CCRT setting

has been completed. It cancels the CCRT setting.

eThe CCRT setting may not be possible with the old cassette tape or

at around the end of the cassette tape. (The CCRT indicator starts

to flash at a high speed.) In this case, press [] and record without

using the CCRT function. (The CCRT indicator goes out.)

oDe not connect or disconnect the microphone while recording.

L__J To cancel the CCRT setting on the

way:

Press N.

CcRTO

To cancel the CCR'I- after the CCRT set-

ting has completed:

Press CC RT.

To erase a recorded sound (Deck 2):

When you make a new recording on a previously recorded tape, the

new recording will automatically erase what was previously re-

corded. To erase a recorded sound without making a new recording,

perform the following steps:

1) Disconnect the microphone if it was connected.

2) Press INT to select the tape mode.

3) Insert the recorded tape intothe cassette holder of deck 2.

4) Press DOLBY NR to light up Dolby NR OUT indicator.

5) Select the desired reverse mode.

6) Press REC PAUSE.

7) Press the playback button (<3 or D) corresponding to the side to

be erased.

To take up the leader tape

The leader tape is the first few revolutions that you cannot record on.

Magnetic tape

(recordings can be made)

Leader tape

(no recordings can be made)

To record with desired tone quality

To record with the desired tone quality, follow the procedure below.

1. Select the desired tone quality. (See pages 42-44.)

2. Follow the procedure of "Making a recording from radio broad-

casts" on page 30.

When playing back such recordings, press ON/FLAT on the tuner/

sound processor to set to "FLAT".

To record without any tonal effect

Press ON/FLAT on the tuner/sound processor to set to "FLAT".

(See pages 42 and 43.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Technics SC-CH515 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info