Bedienungsanleitung Technics SH-MZ1200 (Seite 9 von 16) (Englisch)

536109

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

RQT7230

Mixing (Basic operations)

L/R SPLIT

Press [POWER OFF ON]

The POWER lamp comes on after the power is turned on.

3 Switch the input switch (CD/LINE

DIGITAL, LINE) to select the source

When you select CD/LINE DIGITAL on CH1 or CH4, input can

be analog input (CD/LINE CH1, CH4 input terminal) or digital

input (DIGITAL IN CH1, CH4 input terminal).

4 Turn [TRIM], [HIGH], [MID] and [LOW]

to adjust the input signal level and

sound

TRIM:

Adjusts the input signal level.

Turn to the right for higher sound level (to approximately +8 dB)

Turn to the left for lower sound level (to approximately –8 dB)

HIGH:

Adjusts the high tone input sounds. Sound is flat at the center

position.

Turn to the right to increase sound (to approximately +12 dB at 10 kHz)

Turn to the left to decrease sound (to approximately –24 dB at 10 kHz)

MID:

Adjusts the mid tone input sounds. Sound is flat at the center

position.

Turn to the right to increase sound (to approximately +12 dB at 1 kHz)

Turn to the left to decrease sound (to approximately –24 dB at 1 kHz)

LOW:

Adjusts the low tone input sounds. Sound is flat at the center

position.

Turn to the right to increase sound (to approximately +12 dB at 50 Hz)

Turn to the left to decrease sound (to approximately –24 dB at 50 Hz)

5 Use the channel fader to adjust the

volume

Select the CH2-CH4 source and adjust

volume and sound

(Same as instructions 3 - 5 indicated on the left)

6 When using the cross fader

Turn [ASSIGN A] and [ASSIGN B] to

select the input channel to assign

and

•Select different input channels using the ASSIGN A and

ASSIGN B switches.

If the same input channel is selected by both switches, the

volume will remain unchanged even when the cross fader is

operated.

•The channel selected with ASSIGN A is assigned to , the

channel selected with ASSIGN B is assigned to .

Unassigned channels are not output through the cross fader.

1-4: Assigned channels 1 to 4

THRU: When not using the cross fader

7 When using the cross fader

Use [CROSS FADER] to adjust the

mixing level

The mixing level of the source audio assigned to and is

adjusted by varying the position of the cross fader.

8 Turn [MASTER LEVEL] and [MASTER

BALANCE] to adjust the volume and

balance

Adjust the master output volume and left (L) and

right (R) balance.

•Input source audio from the selected channels CH1-CH4 is

mixed and output through the MASTER OUT 1 left (L) and

(R) terminals.

•Even if the MASTER LEVEL or the MASTER BALANCE is

changed the REC OUT or DIGITAL OUT output does not

change.

1 Turn [L/R SPLIT (CH1 CH2)] and [L/R

SPLIT (CH3 CH4)] to OFF

Select CH1 or CH2 input, CH3 or CH4 input to use the PLAY

MODE's (L) and (R) individual adjustment feature ( page 12).

Using CH1 input

2 Switch [SEPARATE OUT] to OFF

Turn on to activate the play mode SEPARATE OUT function

(

page 12).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Technics SH-MZ1200 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info