Bedienungsanleitung Technics SU-G30 (Seite 44 von 52) (Englisch)

622407

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Troubleshooting

“F ” (“ ” stands for a number.)

• There is a problem with this unit.

- Is the volume extremely high?

If so, lower the volume.

- Is this unit placed in an extremely hot place?

If so, move this unit to a cooler place and wait

a few moments and then try to turn it on

again.

If the problem persists, write down the

displayed number, disconnect the AC mains

lead and consult your dealer.

Load Fail

• The firmware on the USB flash memory cannot

be found.

• Download the latest firmware on the USB flash

memory and try again. ( 38)

No Device

• No USB device is connected.

• Connect the USB device to be played. ( 28)

No Network Available

• This unit is not connected to the network.

• Check the network connection. ( 18)

Not Measured

• Measuring the output signal has not been done

yet.

• Measure the output signal. ( 39)

Not Valid

• The function you have tried to use is not

available with the current settings. Check the

steps and settings.

Please Wait

• This is displayed, for example, when this unit

is turned to standby/on. (For up to approx.

1 minute and 30 seconds)

“Remote

” (“ ” stands for a number.)

• The remote control and this unit are using

different codes.

Change the code on the remote control. ( 15)

Remote Mode

• Basic playback control buttons on the remote

control are not available. (While playing back

music stored on the DLNA server with this unit

(DMR), etc.)

• Use the connected device for basic playback

control.

Searching

• The unit is checking the DLNA server on the

network.

Signal Overflow

• The audio from the analogue audio

input terminal in use is distorted. Select

“Attenuator(LINE)”, and change the setting for

the analogue audio input terminal in use to

“On”. ( 35)

Unlocked

• “PC”, “COAX1”, “COAX2” or “OPT” is selected,

but no device is connected. Check the

connection with the device. ( 32, 33)

• Audio signals, such as sampling frequency

components, are not input correctly.

- About supported format, refer to “File

format” ( 50)

USB Over Current Error

• The iPhone/iPad/iPod or USB device is drawing

too much power. Disconnect the iPhone/iPad/

iPod or USB device and turn the unit to standby

and on again.

Wi-Fi Setup

• Select “On” and press [OK] to enter the

network setting. ( 19)

- To exit the network setting, select “Off” and

press [OK].

Hub Device Not Supported/

Not Supported/

Device Not Recognized/

USB Device Not Supported

• You have connected an iPhone/iPad/iPod or

USB device that is not supported.

- If the iPhone/iPad/iPod is compatible, turn it

on and connect it correctly.

• The format of the file on the iPhone/iPad/iPod

or USB device is not supported.

- About supported format, refer to “File

format” ( 50)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Technics SU-G30 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Technics SU-G30

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info