Bedienungsanleitung Technics SUC700A (Seite 14 von 20) (Englisch)

622405

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

This unit is designed to conserve its power consumption and

save energy. The unit will turn to standby mode automatically

if there is no sound and it is not being used for approximately

20 minutes.

≥ The factory default is “On”.

To cancel this function

1 Press and hold [MUTE] until the PHONO

indicator on this unit starts to blink.

2 Press [MUTE].

Each time you press the button:

3 Press [VOL s] to exit.



≥ You will exit the auto off setup mode if you do not operate any

buttons and controls for approximately 10 seconds after any of the

three indicators above starts blinking.

When other equipment responds to the supplied remote

control, change the remote control code.

≥ The factory default is “1”.

Point the remote control at this unit, and

press and hold [OK] and the numeric button

for at least 4 seconds.

≥When the code is changed, the PC indicator and the

COAX2 indicator blink for approximately 10 seconds.



≥ When the ST-C700A/SL-C700 is connected via the system control

function, change its remote control code as well as the remote

control code for this unit.

You can automatically link this unit with the ST-C700A/SL-

C700 and operate them easily with the remote control.

Preparation

1 Connect this unit and the ST-C700A/SL-C700 with

system connection cables and coaxial digital cables.

(> 10)

2 Set the power switch lever of this unit and the ST-

C700A/SL-C700 to the [Í/I] position.

∫ Switching this unit and the ST-C700A/SL-

C700 to on/standby simultaneously

≥If you point the remote control at this unit and press

[AMP Í] when this unit and the ST-C700A/SL-C700 are in

standby mode, this unit and the device of the selected input

source will be turned on simultaneously.

≥If you point the remote control at this unit and press

[AMP Í] when this unit and the ST-C700A/SL-C700 are

turned on, this unit and the ST-C700A/SL-C700 will

simultaneously enter standby mode.

∫ Switching this unit’s input source

automatically

When you perform an operation such as playback on the ST-

C700A/SL-C700, the input source of this unit will be

automatically switched to “COAX1”/“COAX2”.



≥ For information on the operations of the ST-C700A/SL-C700,

please also refer to their operating instructions.

≥ If you install the dedicated app “Technics Music App” (free of

charge) on your tablet/smartphone, you can use a wide variety of

functions when the unit and the ST-C700A are connected.

For details, visit:

www.technics.com/support/

Auto off function

COAX3 indicator blinks On

OPT indicator blinks Off

Remote control code

[OK] + [1] Set the code to 1

[OK] + [2] Set the code to 2

Using the system control

function

SU-C700_SQTxxxx_EB_EBGN_mst.book 14 ページ２０１５年６月１２日　金曜日　午後４時４分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Technics SUC700A Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info